1/4" Drive - 12 point Universal/Swivel Sockets SAE & METRIC MSRP: Was: Now: $60.00 - $85.00 Choose Options
206/407/505 Swashplate Roll Stake Bearing Work Aid Kit MSRP: Was: Now: $250.00 - $3,000.00 Choose Options
407 Main Rotor Mast Nut Torque Kit With Torque Wrench MSRP: Was: Now: $1,975.00 - $3,175.00 Choose Options
Rolls-Royce 250 HMU "Fuel Control" Throttle/Fly Detent Rigging Pin MSRP: Was: Now: $45.00 Add to Cart
407 Main Rotor Blade Tie Down (4pc Set) Four piece set of main rotor blade tie downs. MSRP: Was: Now: $560.00 Add to Cart
UV Flashlight for Transmission and Engine Oil Leak Checks UV flashlight for detecting oil leaks. Works great in the daytime (with cowlings on), works even better at night. Make sure you wash off your aircraft well before performing a ground run leak check with this light. It will light up ALL your residual oil... MSRP: Was: Now: $30.00 Add to Cart
407 Kaflex Work Aid Here it is, the tool you all have been wanting from us for a while. Ours is made with solid bolts so you don't have the issues that the cables give you Red cover is to protect kaflex shaft during maintenance and while sitting on the... MSRP: Was: Now: $2,250.00 Add to Cart
1/4" Drive - 12 point Universal/Swivel Sockets SAE & METRIC We have located some quality swivel sockets at an affordable price that we are happy to offer here! They are made by Genius Tools. SAE (6pc) set consists of 1/4", 5/16", 3/8", 7/16", 1/2", & 9/16" Metric (9pc) set consists of 6mm, 7mm, 8mm, 9mm,... MSRP: Was: Now: $60.00 - $85.00 Choose Options
407 Pitch Change Universal Bearing PITA Grease Fitting Work Aid Here it is boys and girls. Finally a tool to grease that one pain in the ass grease fitting. No longer will you have to remove the pitch link just to grease the bearing in all 4 spots. Now even your pilot can complete the 50 hour lube. This grease... MSRP: Was: Now: $125.00 Add to Cart
Kaflex Drive Shaft Protective Maintenance Cover Place this pad on the kaflex shaft during maintenance or when removed to protect it from dings and scratches. There are 2 options: 206 and 407. The 206 is a bit longer than the 407. Kaflex definitely not included for this price. MSRP: Was: Now: $50.00 Choose Options
206/407/505 Swashplate Roll Stake Bearing Work Aid Kit Bearing staking tool for the swashplate bearings. Allows you to perform the maintenance on the aircraft without removing the swashplate. T101530 MSRP: Was: Now: $250.00 - $3,000.00 Choose Options
Ultimate Swing Wrench Kit Ultimate Swing Wrench Kits contains 28 pieces. They are: T-handle, Screwdriver handle, and curved handle Open End: 1/4, 5/16, 3/8, 7/16, 1/2, & 9/16 Ratcheting Open End: 5/16 Regular Box End: 1/4, 5/16, 3/8, 7/16, 1/2, & 9/16 Ratcheting Box End:... MSRP: Was: Now: $1,750.00 Add to Cart
Spring Scale 0-50lbs 0-50 lbs Spring Scale. This spring scale is made of brass and will not shatter in your tool box like the cheap plastic spring scales. I've used both, brass and the plastic case spring scales. They both work. I just prefer the brass since they are a... MSRP: Was: Now: $110.00 Add to Cart
Rolls-Royce 250 Fuel Nozzle Holding Fixture Another one where the name of the tool describes it beautifully. Rolls-Royce P/N 6897875 MSRP: Was: Now: $690.00 Add to Cart
206/407/429/505 Adapter Wrench 206L - Freewheeling Unit 407 - Freewheeling Unit 429 - Clutch Assembly 505 - Transmission Input Seal Bell P/N T103306 MSRP: Was: Now: $335.00 Add to Cart
Dykem Cross Check Torque Stripe We have this torque stripe in orange only MSRP: Was: Now: $10.00 Add to Cart
206/407 Intake Plugs and Exhaust Cover Intake plugs come with pitot cover attached together. Your pilot will have to lose the plugs to be able to lose the pitot cover. MSRP: Was: Now: $408.00 - $450.00 Choose Options
ASB 407-23-130 Pilot Cyclic Stick Stop-Drill Work Aid Work aid for ASB 407-23-130 to stop drill cracks on the cyclic stick. 1st drill bushing of .070" listed on ASB not available, Comes with 3 removeable drill bushings and 3 drill bits. #40 .098" #30 .1285" 3/16" ... MSRP: Was: Now: $275.00 Add to Cart
RR250 C20/30/47 Engine Sled Made to fit the C20/C30/C47. Easy assembly and disassembly for shipping. Rolls-Royce P/N 6891189 MSRP: Was: Now: $900.00 Add to Cart
.020" Spherical Inspection Probe This is the spherical radius probe the maintenance manual calls for. This probe has a .020 spherical ball on the very end so that you can run it across the shaft splines to check for damage. Use it on: Multiple 206 items not listed... MSRP: Was: Now: $90.00 Add to Cart
206/407 Airframe Fuel Filter Fixture Requested by a customer, this is a fixture to hold the Airframe Fuel Filter in a vice. Has 4 tabs on it, so you can put the filter in a position that makes it easier for you to work on. MSRP: Was: Now: $85.00 Add to Cart
RR250 Accessory Drive Lip Seal Installs the Starter/Generator and HMU (Fuel Pump) seals on the C47 gearbox MSRP: Was: Now: $140.00 Add to Cart
Engine Wash Bottle SINGLE BOTTLE: This is a stainless, 2 1/2 gallon bottle that has been used by all the major operators in the Gulf of Mexico for the last 45 years to my knowledge. I have replaced the short stock hose with 7 ft of high quality chemical resistant... MSRP: Was: Now: $325.00 - $815.00 Choose Options
407 Kaflex Mounting Wrench If you have ever installed a Kaflex drive shaft, you know how its practically impossible to actually torque them. We designed these wrenches so you could stop using that calibrated elbow and properly torque them with a torque wrench. MSRP: Was: Now: $85.00 Add to Cart
Rolls-Royce 250 Fuel Nozzle Shimming Gauge The simplest gauge for calculating the required shims for the fuel nozzle! We provide instructions that are for reference, but as usual, refer to maintenance manual for latest information. We also have an excel spreadsheet to make... MSRP: Was: Now: $275.00 - $370.00 Choose Options
Rolls-Royce 250 C47 Ratcheting Open-End Fuel-Control Swing Wrench Ratcheting open end swing wrench designed to remove that pesky upper 5/16 nut on the fuel control. With a slow and steady control of the swing wrench, I was able to remove the upper nut in approximately three minutes. Compare that to the last time you... MSRP: Was: Now: $85.00 Add to Cart
Rolls-Royce 250 Turbine To Gearbox Attach Bolt Wrenches - 3pcs No longer will you need to use that calibrated elbow. We have designed 3 wrenches to perform the torque checks on the 6 turbine to gearbox attach bolts on the RR250-C30 and C47 engines. A long 1/4" extension will be required to torque the bolt above the... MSRP: Was: Now: $120.00 Add to Cart
Rolls-Royce 250 C30/C47 Fuel Nozzle Wrench This fuel nozzle wrench is double sided to give you better access to the fuel nozzle. With the cowling installed, if you place the wrench on the fuel nozzle, it may not sit the way you want because of the limited space, flip it to the other side. The... MSRP: Was: Now: $125.00 Add to Cart
Rolls-Royce 250 C30/C47 Medium Fuel Nozzle Wrench This wrench is usually preferred by the overhaul guys working the engine on a stand. MSRP: Was: Now: $95.00 Add to Cart
Bolt Extractor This work aid lets you apply pressure to the bolt while applying penetrating lube. Once the bolt pops loose it can easily be removed. Pressure is applied to the bolt and not to the tail boom fitting. Cracked fittings require tail boom removal at lots of... MSRP: Was: Now: $225.00 Add to Cart
Rolls-Royce 250-C20/C30/C47 Engine Lifting Eye Engine lifting eye for C20, C30, and C47. Long enough to clear the exhaust stack so it doesn't have to be removed. Rolls-Royce C20 6796963Rolls-Royce C30/C47 6889888 MSRP: Was: Now: $475.00 Add to Cart
Bypass Spool Check Mount - With Dial Indicator Bracket held on with nylon screws so as not to damage the servo anodized surface.The bracket also comes with a powder coat finish which gives additional protection to the anodized finish on the servo. MSRP: Was: Now: $2.00 - $255.00 Choose Options
Rolls-Royce 250 Ignitor Wrench Ignitors can be hard to remove for several reasons. Someone put it in too tight, didn't use anti-seize or used a 12 point socket and slipped, rounding off the corners. This wrench is made from a 6 point impact socket. Install the wrench and put the... MSRP: Was: Now: $65.00 Add to Cart
Rolls-Royce 250 Starter/Generator Spline Turn Wrench T-handle wrench for turning the N1 wheels while doing maintenance on the RR250 series engines. Starter/generator splines are hard to find, so get yours here Rolls-Royce P/N 6799790 MSRP: Was: Now: $55.00 Add to Cart
206 & 407 Free Wheeling Unit Aft Flange Wrench Use this work aid by attaching it to the aft flange with two bolts. Use a breaker bar to keep shaft from rotating. Through the larger centered hole, use your socket to torque the nut. We can make the square drive hole 1/2in if you prefer. Bell P/N... MSRP: Was: Now: $85.00 Add to Cart
Reversible Swing Wrenches These reversible swing wrenches are an improvement over our other wrenches. We are using the reversible Gear wrench brand so when you get into a tight spot and can't get the wrench off the nut or bolt you can simply flip the reversing lever and back out... MSRP: Was: Now: $95.00 - $105.00 Choose Options
Brass Screwdriver For Compass Adjustment No more trying to make a screw driver for adjusting compasses with a hammer and welding rod.This is a quality, solid brass screwdriver made especially for adjusting compasses.It's 4 3/4 inches long and the blade tip is 5/32" wide. MSRP: Was: Now: $23.00 Add to Cart
206/407/505 Oil Cooler Blower Driveshaft Spanner Wrench Wrench to get off the spanner nut on the oil cooler blower. The L-model wrench will also work on the 407. MSRP: Was: Now: $70.00 Add to Cart
Bell Rotor Brake Bleeder Kit Oil can comes with 6 feet of hose and allows bleeding the brakes to be a one man job. Fits most Bell models. Quickest way to bleed rotor brakes. MSRP: Was: Now: $38.00 - $168.00 Choose Options
KaFlex Compression Kit for 206L and 407 This is the easiest and fastest way to R&R 206L and 407 KaFlex shafts.Simply make 2 wraps on the driveshaft passing through the holes in the aluminum rods, tie a knot and twist the rods until the cord starts to tighten. Tighten just enough to slip... MSRP: Was: Now: $275.00 Add to Cart
Swing Wrenches Don't buy bulky swing wrenches from tool trucks made from the old ratcheting dog bone wrenches that were great 40 years ago. Ours are made with the slimmer profile Gearwrench ratcheting boxends. Rotor brakes, flight controls in the tailboom, or fuel... MSRP: Was: Now: $85.00 - $95.00 Choose Options
Rolls-Royce 250 Exhaust Stack Wrench Wrench is made for removal of the nuts on the exhaust stack. Keeps nuts from falling into crevices of the engine. MSRP: Was: Now: $30.00 Add to Cart
Composite Tap Hammer Use the tap hammer on main rotor blades or any other composite material to check for delamination. You can order somewhere else for $15 + $12 shipping ($27 total) or just bundle with your next order with us. Equivalent to T75449-2 MSRP: Was: Now: $24.00 Add to Cart
Grease Fitting - Straight These are the threaded ones, not the quick disconnect ones that get grease everywhere except the part you want it in. MSRP: Was: Now: $15.00 Add to Cart
Grease Fitting - 90° These are the threaded ones, not the quick disconnect ones that get grease everywhere except the part you want it in. MSRP: Was: Now: $20.00 Add to Cart
90° Grease Coupler I recently found this 90 degree grease coupler that works great on hard to access grease fittings.Works really well on the oil cooler blower bearings on the Bell 407. It slides in from the side when straight on access is difficult or next to impossible. MSRP: Was: Now: $16.00 Add to Cart
Jackscrews 1/4" 28 - 3pcs Use these on transmission input quills, freewheeling unit, tailrotor gearbox, or any component requiring 1/4" 28 jackscrews. T101308 MSRP: Was: Now: $75.00 Add to Cart
Swashplate Shim Alignment Studs Holds the shims in position when doing the swashplate friction check. The hex head is 5/32" drive.An allen wrench is easier to get in to tight areas than a long phillips screwdriver. Can also be used as jack screws on the 206 and 407 transmission input... MSRP: Was: Now: $20.00 Add to Cart
Rolls-Royce 250 C30/C47 Gearbox PTO Seal Installer This installer works on the C30 and C47 engines. You can install one seal at a time or both at once. This is the best seal installer you will find for the gearbox seals. MSRP: Was: Now: $825.00 Add to Cart
Rolls-Royce 250 C30/C47 Gearbox PTO Seal Remover Removes rear gearbox seal. MSRP: Was: Now: $725.00 Add to Cart
Rolls-Royce 250 C30/C47 Bleed Valve Shop Air Adapter Quick disconnect so that you can use shop air to close the Bleed valve. MSRP: Was: Now: $40.00 Add to Cart
Rolls-Royce 250 Quick Disconnect Coupling For Engine Rinse Name says it all. MSRP: Was: Now: $45.00 Add to Cart
Saft Battery Cap Pressure Tester This manifold is for pressure testing the saft battery caps. We will need you to send us the caps you want the manifold manufactured for. MSRP: Was: Now: $250.00 Add to Cart
206 & 407 Tailboom Maintenance Stand 206 & 407 Tailboom Maintenance StandCall for more information.Maintains tailboom at chest level for maintenance. Able to rotate 360 degrees. MSRP: Was: Now: $0.00 Add to Cart
Rolls-Royce 250 Power Turbine Support Cleaning Kit Kit comes in a foam insert for easy storage and handling. Keep the cardboard box it comes in for added protection. RR P/N 23007615 MSRP: Was: Now: $175.00 Add to Cart
Torque Adapters 1/4" Drive Hard to find 1/4" drive torque adapters. Most torque adapters you will find are 3/8" drive. These will allow you to use that low torque 1/4" torque wrench without the 3/8" to 1/4" adapter. SAE: The standard set consists of 1/4", 5/16", 3/8", &... MSRP: Was: Now: $50.00 - $170.00 Choose Options
206 & 407 Transmission Oil Pump Puller Slide hammer for transmission oil pump on 206s and 407s. MSRP: Was: Now: $150.00 Add to Cart
407 Lifting Clevis T102137-107 T102137-111Not much to say about this item. I think everyone knows what it's for. MSRP: Was: Now: $1,975.00 Add to Cart
407 Pitch Link Tension Reliever Used to move the blade and grip when trying to re-connect the pitch change links. MSRP: Was: Now: $285.00 Add to Cart
407 HTS900 Accessory Gearbox Drain Oil drain hose for the accessory gearbox on the 407 powered by the Honeywell engine.Won't find too many of these out there. Comes with a 7 ft hose. MSRP: Was: Now: $90.00 Add to Cart
407 Transmission Restraint Spring Alignment Bullet Used to align the restraint spring during installation MSRP: Was: Now: $42.00 Add to Cart
407 Expandable Blade Bolt Inspection Work Aid Expandable blade bolts require 600 hour or 12 month inspection. Those inspections require removing the segments on the expandable bolts and inspecting for corrosion and wear. This work aid assists by maintaining all the segments in the proper order... MSRP: Was: Now: $75.00 Add to Cart
407 Tail Rotor Mast Nut Wrench Use this wrench to torque and perform torque checks of the 407 tailrotor mast nut. Pull quick release pin and slide wrench onto mast nut. Use 3/8 drive torque wrench. This wrench fits better than the large bulky crowsfoot. Send us a scrap tail... MSRP: Was: Now: $275.00 Add to Cart
407 Hydraulic Pump Wrenches Each set consists of an open end and a box end wrench for fast R&R of the hydraulic pump. You have to try these to see how well they work. If you don't like these wrenches I will refund your money and pay shipping both ways. That's how much... MSRP: Was: Now: $110.00 Add to Cart
407 Tailboom Torque Check Socket 9/16" 12 point socket per Bell specs to comply with the 407 tailboom torque checks due every 300 hours on ASB-407-10-93. Bell P/N 407-230-001-101 Also helps comply with: ASB 407-24-134 ASB 407-22-128 AD 2022-27-08 AD CF-2022-68 MSRP: Was: Now: $40.00 Add to Cart
407 Main Rotor Pitch Change Link Trammel Trammel made especially for the 407 main rotor pitch change link. Trammel adjusts to fit the old link.Pull the round pin out and install the new link.Adjust the new link until the round pin slides back into the hole. Tighten the link jam nuts and... MSRP: Was: Now: $480.00 Add to Cart
407 Corner Mount Puller 407-240-013-107This puller is used to aid in the lifting of the corner mounts during replacement of pads. MSRP: Was: Now: $1,995.00 Add to Cart
407 Tail Rotor Rigging Block Color varies when manufactured Used with the 407 tail rotor flap stop work aid to check or rig the tail rotor system. Ours (Helicopter Work Aids) is 3D Printed, made with PLA. Very tough but not as heavy as the steel blocks that Bell... MSRP: Was: Now: $245.00 Choose Options
407 Tail Rotor Flap Lock Work Aid For Rigging This work aid is used to stop the tail rotor from flapping when checking the blade pitch angles. This is used in conjunction with the 407 tailrotor rigging block which is used to check the pitch angle. Bell P/N 407-99-26-101 found in ASB... MSRP: Was: Now: $425.00 Add to Cart
407 Tail Rotor Flap Stop This work aid is used to stop the tail rotor from flapping when checking the blade pitch angles. This is used in conjunction with the 407 tailrotor rigging block which is used to check the pitch angle. This is our lightweight 3D printed... MSRP: Was: Now: $285.00 Add to Cart
407 Collective Pitch Transducer Work Aid Work aid to help rig the collective pitch transducer. MSRP: Was: Now: $35.00 Add to Cart
407 Hydraulic Filter Bypass Dummy hydraulic filters perform check of hydraulic filter differential pressure indicator. Reference 407 MM Chap 29-30. Pro-tip: MM calls out for hydraulic mule, but this test can be performed by installing dummy filters and spinning rotor by hand... MSRP: Was: Now: $45.00 - $75.00 Choose Options
407 Torque Reactor Pin Used with your choice of a 4-1 or 3-1 torque multiplier. 407 back up pin in use. Let the torque multiplier bump up against the pin to hold backup.This pin lets you do the mast nut torque or 1-5 hr torque check by yourself not to mention holding... MSRP: Was: Now: $435.00 Add to Cart
206/407 Transmission Oil Pump & Housing Assembly Work Aid If you're looking for this, you already know what it's for. TB206L-05-218 TB407-05-65 MSRP: Was: Now: $135.00 Add to Cart
407 Transmission Drain Each drain comes with a 7 ft. hose. Bell P/N H4713 MSRP: Was: Now: $95.00 Add to Cart
407 Tail Rotor Gearbox Drain Tail rotor gearbox drain with a 7 foot hose. Bell P/N H4749 MSRP: Was: Now: $95.00 Add to Cart
407 Fuel Tank Drain Draining the tank for fuel calibration or any type of fuel tank maintenance is now a piece of cake. No more taping a tongue depressor/wooden stick/whatever you have laying around or holding the sump button until your finger feels like it is going to fall... MSRP: Was: Now: $105.00 Add to Cart
TB407-18-127 Vertical Fin Tail Skid Mod Fixture, bushings and bolts needed to locate and drill new hole in vertical fin tail skid p/n 206-020-110-103 at the attachment hole location.Lead time is about 4-5 weeks as the bushings and bolts must be ordered from an outside supplier. And they are... MSRP: Was: Now: $525.00 Add to Cart
407 Tail Rotor Driveshaft Alignment Work Aid Complies with ASB-407-16-113 to align driveshafts. T102146-101 MSRP: Was: Now: $895.00 Add to Cart
407 Tail Rotor Driveshaft Coupling Nut Wrench AD 2018-10-06 We designed this wrench to comply with 407 AD 2018-10-06 for torquing the coupling nuts on the tailrotor driveshaft. With this wrench, there is no need to remove the driveshaft, only the Thomas coupling. This wrench can also be used to torque the... MSRP: Was: Now: $60.00 Add to Cart
407 Air Conditioner Spanner Wrench Facilitates maintenance on air conditioner MSRP: Was: Now: $85.00 Add to Cart
407 Air Conditioner Pulley Wrench This air conditioner pulley wrench avoids elongating the pin hole when using a pin spanner, plus it stays in place when torquing. MSRP: Was: Now: $135.00 Add to Cart
407 Blade Bolt Bullets Never fight with the main rotor blade again! With these bullets you can get the blade mostly in place and just push the bolts through! The bullets keep the shoulders of the bolt from catching. The new guy you have leaning off a ladder, holding up the... MSRP: Was: Now: $150.00 Add to Cart
407 Frahm Cover Bit This is the apex bit for the 407 Frahm cover. Everybody on the crew needs one and this is where you can find them. MSRP: Was: Now: $14.50 Add to Cart
407 Horizontal Stabilizer Bit Reduced shank #2 Phillips bit for removing and installing the screws in the slats on the 407 horizontal stabilizer. Previously P/N: 5750A89 MSRP: Was: Now: $4.00 Add to Cart
407 Transmission Input Flange Wrench Transmission input flange wrench for the 407. MSRP: Was: Now: $335.00 Add to Cart
206/407 Hydraulic Pump Shaft Remover Work aid that helps easily remove the hydraulic pump shaft. You will no longer need to pry out the shaft with pliers and have the shaft and spring flying across the hangar, or worse, a grassy field. Open the shaft remover and place it around the... MSRP: Was: Now: $195.00 Add to Cart
407 Transmission Corner Mount Nut Socket 2532 Why Bell would decide to use a 25/32" socket on the transmission corner mount we will never know..... They are not very common but we found a supplier that has the 1/2" drive, 12 point deep socket that works great. MSRP: Was: Now: $24.00 Add to Cart
407 Main Rotor Assy Alignment Guide and Thread Protector Threads on to the end of the mast to act as a guide for installation and also protects the mast nut threads during maintenance. MSRP: Was: Now: $255.00 Add to Cart
407 Main Rotor Head Sling Sling for removing rotor head. Blades should not be installed when rotor head is being removed. Picture shows sling in use.If you are using the guide and mast thread protector a longer strap is required. Let us know if you are using the thread protector... MSRP: Was: Now: $310.00 Add to Cart
407 Main Rotor 1-1/4" Mast Nut Socket 1-1/4 impact socket for the Main Rotor Mast Nut. 3/4" and 1" drive available MSRP: Was: Now: $68.00 Choose Options
407 Transmission Cover And Lift Plate Cover plates for the 407 transmissions. Fitted with eye for lifting transmission. NOT for lifting aircraft.Lifting eye is rated for 9000 lbs Bell P/N T103314 MSRP: Was: Now: $390.00 Add to Cart
Bell 407 Tailboom/Fuselage Former Ring Fixture Used for replacing tailboom/fuselage former ring or tail boom attach fittings on the Bell 407 only.The top two holes are larger than the 206. This fixture comes with 2 drill bushings. One for the top holes and one for the bottom holes. A 3/16... MSRP: Was: Now: $900.00 Add to Cart
RR250 C30/C47 Compressor/Diffuser Orifice R&R Work Aid Use this work aid to remove and re-install the orifice when it is located in the exhaust collector.Good on any 206L with C30 installed, 407, and Sikorsky S-76A. MSRP: Was: Now: $85.00 Add to Cart
407 Main Rotor Mast Nut Torque Kit This kit includes everything you need to torque the mast nut on the 407 main rotor except for the 600 lb torque wrench. It has a 3-1 torque multiplier, the torque reactor pin to hold a back up and the 1 1/4" 1 inch drive impact socket.It... MSRP: Was: Now: $1,600.00 Add to Cart
407 Main Rotor Mast Nut Torque Kit With Torque Wrench This kit includes everything you need to torque the mast nut on the 407 main rotor including the 600 lb torque wrench made by Performance Tool. These are very good quality wrenches. It has a 3-1 torque multiplier, the torque reactor pin to hold... MSRP: Was: Now: $1,975.00 - $3,175.00 Choose Options
Rolls-Royce 250 C47 Engine Gearbox Drain As you know, the C47 has the quick disconnect chip detectors that have the self plugging housing. Unlike the C30's that will drain when you pull the chip detectors, the C47 requires this work aid to drain the gearbox. This drain is made from steel. MSRP: Was: Now: $105.00 Add to Cart
Rolls-Royce 250 HMU "Fuel Control" Throttle/Fly Detent Rigging Pin Easy to handle rigging pin with red streamer. MSRP: Was: Now: $45.00 Add to Cart
Air Conditioner Belt Tensiometer Belt Tensiometer specified by Bell for checking air conditioning belt tension. Scale reads in pounds and kilograms Measures tension from 30 to 160 lb., and 15 to 75 kg. Die-cast aluminum body, nylon indicator arm and pressure pad Fits in pocket... MSRP: Was: Now: $30.00 Add to Cart
Rolls-Royce 250 Oil Pressure Regulator Socket 1/4 inch drive socket for adjusting the oil pressure regulator.Makes it easy to adjust and count the turns plus it won't eat up the regulator adjusting bar when using needle nose pliers like other people used to do. MSRP: Was: Now: $45.00 Add to Cart
Rolls-Royce 250 Turbine Wheel Lock Used to lock the turbine wheel in place when installing the turbine section. The plate and rod are made from brass. The brass rod is soft enough to bend if necessary so it won't damage the turbine blades should excessive pressure be applied to the... MSRP: Was: Now: $65.00 Add to Cart
407 Tail Rotor Gearbox Wrench 407 tail rotor gearbox wrench to properly torque the aft left hand nut. MSRP: Was: Now: $75.00 Add to Cart
206L/407/429 CORDLESS Portable Hydraulic Pump Drive Unit Remove the hydraulic pump from the transmission with the hoses still connected and bolt hydraulic pump to the red pump pressure supply. The Cordless Makita is driven by a soft start, 5 speed, variable speed drive. You can finally lay to... MSRP: Was: Now: $4,900.00 Add to Cart
