Rolls-Royce 250 HMU "Fuel Control" Throttle/Fly Detent Rigging Pin MSRP: Was: Now: $45.00 Add to Cart
Rolls-Royce 250 Starter/Generator Seal Installer & Fuel Pump Seal Installer - 2pcs MSRP: Was: Now: $145.00 Add to Cart
RR250 C20/30/47 Engine Sled Made to fit the C20/C30/C47. Easy assembly and disassembly for shipping. MSRP: Was: Now: $900.00 Add to Cart
RR250 Spur Adapter Gear Installation Work Aid P/N: 250SG2 (C20 only) Rolls-Royce P/N 23006778 P/N 250SG3 (C30 & C47) Rolls-Royce P/N 23005426 MSRP: Was: Now: $240.00 Choose Options
RR250 Accessory Drive Lip Seal Installs the Starter/Generator and HMU (Fuel Pump) seals on the C47 gearbox MSRP: Was: Now: $140.00 Add to Cart
Engine Wash Bottle SINGLE BOTTLE: This is a stainless, 2 1/2 gallon bottle that has been used by all the major operators in the Gulf of Mexico for the last 45 years to my knowledge. I have replaced the short stock hose with 7 ft of high quality chemical resistant... MSRP: Was: Now: $325.00 - $815.00 Choose Options
Rolls-Royce 250 Fuel Nozzle Shimming Gauge The simplest gauge for calculating the required shims for the fuel nozzle! We provide instructions that are for reference, but as usual, refer to maintenance manual for latest information. We also have an excel spreadsheet to make... MSRP: Was: Now: $275.00 Add to Cart
Rolls-Royce 250 C47 Ratcheting Open-End Fuel-Control Swing Wrench Ratcheting open end swing wrench designed to remove that pesky upper 5/16 nut on the fuel control. With a slow and steady control of the swing wrench, I was able to remove the upper nut in approximately three minutes. Compare that to the last time you... MSRP: Was: Now: $85.00 Add to Cart
Rolls-Royce 250 C20 Compressor Case Half Wrenches - 3pcs set With these wrenches, you can now cut down the time it takes to disassemble the case halves by 50%. Bits are removable which allows you to use the reverse side of the ratchet for removal and installation with just our two ratcheting wrenches. Comes with a... MSRP: Was: Now: $350.00 Add to Cart
Rolls-Royce 250 C20 Gearbox Seal Installer Rolls-Royce 250 C20 Gearbox Seal InstallerP/N: 250GSIInstalls the gearbox seals on the C20's. Place guide on output shaft, place seal over the guide, and place flange over the seal. Use supplied nuts and washers to pull flange into place, pressing the... MSRP: Was: Now: $300.00 Add to Cart
Rolls-Royce 250 Turbine To Gearbox Attach Bolt Wrenches - 3pcs WRENCHES HAVE BEEN ORDERED. WE ARE AWAITING ARRIVAL TO MAKE THESE AGAIN. No longer will you need to use that calibrated elbow. We have designed 3 wrenches to perform the torque checks on the 6 turbine to gearbox attach bolts on the RR250-C30 and C47... MSRP: Was: Now: $120.00
Rolls-Royce 250 C30/C47 Fuel Nozzle Wrench This fuel nozzle wrench is double sided to give you better access to the fuel nozzle. With the cowling installed, if you place the wrench on the fuel nozzle, it may not sit the way you want because of the limited space, flip it to the other side. The... MSRP: Was: Now: $110.00 Add to Cart
Rolls-Royce 250 C30/C47 Medium Fuel Nozzle Wrench This wrench is usually preferred by the overhaul guys working the engine on a stand. MSRP: Was: Now: $95.00 Add to Cart
206B Bleed Valve Block Color varies when manufactured Bleed valve block for Rolls-Royce C20 engine with strap so that it can be hung. Rolls-Royce P/N 6886204 MSRP: Was: Now: $38.00 Add to Cart
Rolls-Royce C30/C47 Engine Lifting Eye Engine lifting eye for C30 and C47. Long enough to clear the exhaust stack so it doesn't have to be removed. There are 3 3/8-24 threaded holes so the bolts can be stored when not in use. Rolls-Royce C20 6796963Rolls-Royce C30/C47... MSRP: Was: Now: $335.00 Add to Cart
Bypass Spool Check Mount - With Dial Indicator Bypass Spool Check MountP/N: 24SBDI - (with Dial Indicator)Bracket held on with nylon screws so as not to damage the servo anodized surface.The bracket also comes with a powder coat finish which gives additional protection to the anodized... MSRP: Was: Now: $80.00 - $255.00 Choose Options
Rolls-Royce 250 Ignitor Wrench Ignitors can be hard to remove for several reasons. Someone put it in too tight, didn't use anti-seize or used a 12 point socket and slipped, rounding off the corners. This wrench is made from a 6 point impact socket. Install the wrench and put the... MSRP: Was: Now: $65.00 Add to Cart
Rolls-Royce 250 Starter/Generator Spline Turn Wrench T-handle wrench for turning the N1 wheels while doing maintenance on the RR250 series engines. Starter/generator splines are hard to find, so get yours here MSRP: Was: Now: $55.00 Add to Cart
Rolls-Royce C20 Engine Lifting Eye Engine lifting eye for C20 Long enough to clear the exhaust stack so it doesn't have to be removed. There are 3 3/8-24 threaded holes so the bolts can be stored when not in use. Rolls-Royce P/N C20 6796963 Rolls-Royce P/N C30/C47 6889888 MSRP: Was: Now: $335.00 Add to Cart
Rolls-Royce 250 Idle Adjustment Swing Wrench This swing wrench is made specifically for adjusting the idle on the 206 RR250 engine. Of course with that in mind, you can also use it for any tight spot that requires a 1/4" box end wrench. We have 2 types of swing wrenches. Our version and Helitools'... MSRP: Was: Now: $85.00 Choose Options
Rolls-Royce 250 Exhaust Stack Wrench Wrench is made for removal of the nuts on the exhaust stack. Keeps nuts from falling into crevices of the engine. MSRP: Was: Now: $30.00 Add to Cart
Rolls-Royce 250 C30/C47 Gearbox PTO Seal Installer This installer works on the C30 and C47 engines. You can install one seal at a time or both at once. This is the best seal installer you will find for the gearbox seals. MSRP: Was: Now: $825.00 Add to Cart
Rolls-Royce 250 C30/C47 Gearbox PTO Seal Remover Removes rear gearbox seal. MSRP: Was: Now: $725.00 Add to Cart
Rolls-Royce 250 C30/C47 Bleed Valve Shop Air Adapter Quick disconnect so that you can use shop air to close the Bleed valve. MSRP: Was: Now: $40.00 Add to Cart
Rolls-Royce 250 Quick Disconnect Coupling For Engine Rinse Name says it all. MSRP: Was: Now: $45.00 Add to Cart
Rolls-Royce 250 Power Turbine Support Cleaning Kit Kit comes in a foam insert for easy storage and handling. Keep the cardboard box it comes in for added protection. MSRP: Was: Now: $175.00 Add to Cart
RR250 C30/C47 Compressor/Diffuser Orifice R&R Work Aid RR250 C30/C47 Compressor/Diffuser Orifice R&R Work AidP/N: 250CDOUse this work aid to remove and re-install the orifice when it is located in the exhaust collector.Good on any 206L with C30 installed, 407, and Sikorsky S-76A. MSRP: Was: Now: $85.00 Add to Cart
Rolls-Royce 250 C47 Engine Gearbox Drain As you know, the C47 has the quick disconnect chip detectors that have the self plugging housing. Unlike the C30's that will drain when you pull the chip detectors, the C47 requires this work aid to drain the gearbox. This drain is made from steel. MSRP: Was: Now: $105.00 Add to Cart
Rolls-Royce 250 HMU "Fuel Control" Throttle/Fly Detent Rigging Pin Rolls-Royce 250 HMU "Fuel Control" Throttle/Fly Detent Rigging PinP/N: 407HMUEasy to handle rigging pin with red streamer. MSRP: Was: Now: $45.00 Add to Cart
Rolls-Royce 250 C20 Starter/Generator Seal Installer This is the new seal installer from Rolls-Royce's Commercial Service Letter. This was designed for installing the new lip seals (23091467) which include a supplied installation mandrel.Although it will also work on the old lip seals (23079054) we,... MSRP: Was: Now: $165.00 Add to Cart
Rolls-Royce RR300 Seal Installer Rolls-Royce RR300 Seal Installer P/N: 250SGSIThis is the new seal installer from Rolls-Royce's Commercial Service Letter. This was designed for installing the new lip seals (23091467) which include a supplied installation mandrel. MSRP: Was: Now: $165.00 Add to Cart
Rolls-Royce 300 Aft PTO Seal Installer Rolls-Royce 300 Aft PTO Seal InstallerP/N: R66SIName describes it all. MSRP: Was: Now: $1,050.00 Add to Cart
Rolls-Royce 300 Aft PTO Seal Remover Rolls-Royce 300 Aft PTO Seal RemoverP/N: R66SRName describes it all. MSRP: Was: Now: $2,000.00 Add to Cart
Rolls-Royce 250 Oil Pressure Regulator Socket 1/4 inch drive socket for adjusting the oil pressure regulator.Makes it easy to adjust and count the turns plus it won't eat up the regulator adjusting bar when using needle nose pliers like other people used to do. MSRP: Was: Now: $45.00 Add to Cart
Rolls-Royce 250 Turbine Wheel Lock Used to lock the turbine wheel in place when installing the turbine section. The plate and rod are made from brass. The brass rod is soft enough to bend if necessary so it won't damage the turbine blades should excessive pressure be applied to the... MSRP: Was: Now: $65.00 Add to Cart
St. Gobain PTO Seal Installer - C20 St. Gobain PTO Seal Installer - C20P/N: PTOSEAL C20These are the seal installers for the new St Gobain seals p/n 23091293 (red) and p/n 23091353 (blue)They can also be used for installing the Viton SealsThe C20 and C30/47 have different seal insertion... MSRP: Was: Now: $275.00 Add to Cart
Gobain PTO Seal Installer - C30/C47 St. Gobain PTO Seal Installer - C20P/N: PTOSEAL C30/47These are the seal installers for the new St Gobain seals p/n 23091293 (red) and p/n 23091353 (blue)They can also be used for installing the Viton SealsThe C20 and C30/47 have different seal insertion... MSRP: Was: Now: $275.00 Add to Cart
O'Ring Spur Adapter Gear Installation Work Aid For engines C30 and C47 only MSRP: Was: Now: $410.00 Add to Cart
Rolls-Royce 250 Starter/Generator Seal Installer & Fuel Pump Seal Installer - 2pcs This work aid is a 2 in 1. Use it on either the starter/generator seal or the fuel pump seal. Simplifies installation of seals and removes chances of damaging seal while installing. This work aid is only for lip seal (23079054). MSRP: Was: Now: $145.00 Add to Cart
Rolls-Royce 250 C30 PTO Seal Remover For S76A & BO-105 Used to remove single lip PTO seal on C30 engines. Thread into the seal and use slide hammer to remove. MSRP: Was: Now: $525.00 Add to Cart
