407 Main Rotor Mast Nut Torque Kit With Torque Wrench MSRP: Was: Now: $2,850.00 - $4,450.00 Choose Options
Rolls-Royce 250 HMU "Fuel Control" Throttle/Fly Detent Rigging Pin MSRP: Was: Now: $45.00 Add to Cart
Rolls-Royce 250 Starter/Generator Seal Installer & Fuel Pump Seal Installer - 2pcs MSRP: Was: Now: $145.00 Add to Cart
206/407/505 Tail Rotor Gearbox Input/Output Bearing Retaining Nut Wrench MSRP: Was: Now: $425.00 Add to Cart
206/407/505 Freewheeling Unit Shaft Removal Work Aids MSRP: Was: Now: $150.00 - $450.00 Choose Options
407 Tail Rotor Drive Shaft Balancing Oil Reservoir Attachment Bracket MSRP: Was: Now: $85.00 Add to Cart
Jackscrews 1/4" 28 - 3pcs Use these on transmission input quills, freewheeling unit, tailrotor gearbox, or any component requiring 1/4" 28 jackscrews. T101308 MSRP: Was: Now: $75.00 Add to Cart
206/407/505 Swashplate Shim Alignment Studs Holds the shims in position when doing the swashplate friction check. The hex head is 5/32" drive.An allen wrench is easier to get in to tight areas than a long phillips screwdriver. Can also be used as jack screws on the 206 and 407 transmission input... MSRP: Was: Now: $45.00 Add to Cart
Rolls-Royce 250 C30/C47 Gearbox PTO Seal Installer This installer works on the C30 and C47 engines. You can install one seal at a time or both at once. This is the best seal installer you will find for the gearbox seals. MSRP: Was: Now: $825.00 Add to Cart
Rolls-Royce 250 C30/C47 Gearbox PTO Seal Remover Removes rear gearbox seal. MSRP: Was: Now: $725.00 Add to Cart
Rolls-Royce 250 C30/C47 Bleed Valve Shop Air Adapter Quick disconnect so that you can use shop air to close the Bleed valve. MSRP: Was: Now: $40.00 Add to Cart
Rolls-Royce 250 Quick Disconnect Coupling For Engine Rinse Name says it all. MSRP: Was: Now: $45.00 Add to Cart
Saft Battery Cap Pressure Tester This manifold is for pressure testing the saft battery caps. We will need you to send us the caps you want the manifold manufactured for. Pictured are two different battery caps. If the battery cap is a common thread, we can make the work aid with... MSRP: Was: Now: $250.00 Add to Cart
Rolls-Royce 250 Power Turbine Support Cleaning Kit Kit comes in a foam insert for easy storage and handling. RR P/N 23007615 RR P/N 23003267 MSRP: Was: Now: $175.00 Add to Cart
Torque Adapters 1/4" Drive Hard to find 1/4" drive torque adapters. Most torque adapters you will find are 3/8" drive. These will allow you to use that low torque 1/4" torque wrench without the 3/8" to 1/4" adapter. SAE: The standard set consists of 1/4", 5/16", 3/8", &... MSRP: Was: Now: $50.00 - $200.00 Choose Options
206 & 407 Transmission Oil Pump Puller Slide hammer for transmission oil pump on 206s and 407s. MSRP: Was: Now: $150.00 Add to Cart
407 Lifting Clevis T102137-107 T102137-111​Not much to say about this item. I think everyone knows what it's for. MSRP: Was: Now: $1,975.00 Add to Cart
407 Pitch Link Tension Reliever Used to move the blade and grip when trying to re-connect the pitch change links. MSRP: Was: Now: $285.00 Add to Cart
407 HTS900 Accessory Gearbox Drain Oil drain hose for the accessory gearbox on the 407 powered by the Honeywell engine.Won't find too many of these out there. Comes with a 7 ft hose. MSRP: Was: Now: $90.00 Add to Cart
407 Transmission Restraint Spring Alignment Bullet Used to align the restraint spring during installation MSRP: Was: Now: $42.00 Add to Cart
407 Expandable Blade Bolt Inspection Work Aid Expandable blade bolts require 600 hour or 12 month inspection. Those inspections require removing the segments on the expandable bolts and inspecting for corrosion and wear. This work aid assists by maintaining all the segments in the proper order... MSRP: Was: Now: $75.00 Add to Cart
407 Tail Rotor Mast Nut Wrench Use this wrench to torque and perform torque checks of the 407 tailrotor mast nut. Pull quick release pin and slide wrench onto mast nut. Use 3/8 drive torque wrench. This wrench fits better than the large bulky crowsfoot. Send us a scrap tail... MSRP: Was: Now: $275.00 Add to Cart
407 Hydraulic Pump Wrenches Each set consists of an open end and a box end wrench for fast R&R of the hydraulic pump. You have to try these to see how well they work. If you don't like these wrenches I will refund your money and pay shipping both ways. That's how much... MSRP: Was: Now: $110.00 Add to Cart
407 Tail Boom Torque Check Socket 9/16" 12 point socket per Bell specs to comply with the 407 tailboom torque checks due every 300 hours on ASB-407-10-93. Bell P/N 407-230-001-101 Also helps comply with: ASB 407-24-134 ASB 407-22-128 AD 2022-27-08 AD CF-2022-68 MSRP: Was: Now: $40.00 Add to Cart
407 Main Rotor Pitch Change Link Trammel Trammel made especially for the 407 main rotor pitch change link. Trammel adjusts to fit the old link.Pull the round pin out and install the new link.Adjust the new link until the round pin slides back into the hole. Tighten the link jam nuts and... MSRP: Was: Now: $535.00 Add to Cart
407 Corner Mount Puller 407-240-013-101This puller is used to aid in the lifting of the corner mounts during replacement of pads. New & Improved with ACME Thread and thrust bearing on the rotating pusher. MSRP: Was: Now: $1,995.00 Add to Cart
407 Tail Rotor Rigging Block Color varies when manufactured Used with the 407 tail rotor flap stop work aid to check or rig the tail rotor system. Ours (Helicopter Work Aids) is 3D Printed, made with PLA. Very tough but not as heavy as the steel blocks that Bell... MSRP: Was: Now: $245.00 Choose Options
407 Tail Rotor Flap Lock Work Aid For Rigging This work aid is used to stop the tail rotor from flapping when checking the blade pitch angles. This is used in conjunction with the 407 tailrotor rigging block which is used to check the pitch angle. Bell P/N 407-99-26-101 found in ASB... MSRP: Was: Now: $425.00 Add to Cart
407 Tail Rotor Flap Stop This work aid is used to stop the tail rotor from flapping when checking the blade pitch angles. This is used in conjunction with the 407 tailrotor rigging block which is used to check the pitch angle. This is our lightweight 3D printed... MSRP: Was: Now: $285.00 Add to Cart
407 Collective Pitch Transducer Work Aid Work aid to help rig the collective pitch transducer. MSRP: Was: Now: $35.00 Add to Cart
407 Hydraulic Filter Bypass Dummy hydraulic filters perform check of hydraulic filter differential pressure indicator. Reference 407 MM Chap 29-30. Pro-tip: MM calls out for hydraulic mule, but this test can be performed by installing dummy filters and spinning rotor by hand... MSRP: Was: Now: $75.00 - $135.00 Choose Options
407 Torque Reactor Pin Used with your choice of a 4-1 or 3-1 torque multiplier. 407 back up pin in use. Let the torque multiplier bump up against the pin to hold backup.This pin lets you do the mast nut torque or 1-5 hr torque check by yourself not to mention holding... MSRP: Was: Now: $435.00 Add to Cart
206/407 Transmission Oil Pump & Housing Assembly Work Aid If you're looking for this, you already know what it's for. TB206L-05-218 TB407-05-65 MSRP: Was: Now: $135.00 Add to Cart
407 Transmission Drain Each drain comes with a 7 ft. hose. Bell P/N H4713 MSRP: Was: Now: $95.00 Add to Cart
407 Tail Rotor Gearbox Drain Tail rotor gearbox drain with a 7 foot hose. Bell P/N H4749 MSRP: Was: Now: $95.00 Add to Cart
407 Fuel Tank Drain Draining the tank for fuel calibration or any type of fuel tank maintenance is now a piece of cake. No more taping a tongue depressor/wooden stick/whatever you have laying around or holding the sump button until your finger feels like it is going to fall... MSRP: Was: Now: $105.00 Add to Cart
TB407-18-127 Vertical Fin Tail Skid Mod Fixture, bushings and bolts needed to locate and drill new hole in vertical fin tail skid p/n 206-020-110-103 at the attachment hole location.Lead time is about 4-5 weeks as the bushings and bolts must be ordered from an outside supplier. And they are... MSRP: Was: Now: $525.00 Add to Cart
407 Tail Rotor Driveshaft Alignment Work Aid Complies with ASB-407-16-113 to align driveshafts. T102146-101 MSRP: Was: Now: $895.00 Add to Cart
407 Tail Rotor Driveshaft Coupling Nut Wrench AD 2018-10-06 We designed this wrench to comply with 407 AD 2018-10-06 for torquing the coupling nuts on the tailrotor driveshaft. With this wrench, there is no need to remove the driveshaft, only the Thomas coupling. This wrench can also be used to torque the... MSRP: Was: Now: $60.00 Add to Cart
407 Air Conditioner Spanner Wrench Facilitates maintenance on air conditioner MSRP: Was: Now: $185.00 Add to Cart
407 Air Conditioner Pulley Wrench This air conditioner pulley wrench avoids elongating the pin hole when using a pin spanner, plus it stays in place when torquing. MSRP: Was: Now: $175.00 Add to Cart
407 Blade Bolt Bullets Never fight with the main rotor blade again! With these bullets you can get the blade mostly in place and just push the bolts through! The bullets keep the shoulders of the bolt from catching. The new guy you have leaning off a ladder, holding up the... MSRP: Was: Now: $150.00 Add to Cart
407 Frahm Cover Bit This is the apex bit for the 407 Frahm cover. Everybody on the crew needs one and this is where you can find them. MSRP: Was: Now: $14.50 Add to Cart
407 Horizontal Stabilizer Bit Reduced shank #2 Phillips bit for removing and installing the screws in the slats on the 407 horizontal stabilizer. Previously P/N: 5750A89 MSRP: Was: Now: $4.00 Add to Cart
407 Transmission Input Flange Wrench Transmission input flange wrench for the 407. 407-240-010-101 MSRP: Was: Now: $335.00 Add to Cart
206/407 Hydraulic Pump Shaft Remover Work aid that helps easily remove the hydraulic pump shaft. You will no longer need to pry out the shaft with pliers and have the shaft and spring flying across the hangar, or worse, a grassy field. Open the shaft remover and place it around the... MSRP: Was: Now: $195.00 Add to Cart
407 Transmission Corner Mount Nut Socket 2532 Why Bell would decide to use a 25/32" socket on the transmission corner mount we will never know..... They are not very common but we found a supplier that has the 1/2" drive, 12 point deep socket that works great. MSRP: Was: Now: $24.00 Add to Cart
407 Main Rotor Assy Alignment Guide and Thread Protector Threads on to the end of the mast to act as a guide for installation and also protects the mast nut threads during maintenance. MSRP: Was: Now: $255.00 Add to Cart
407 Main Rotor Head Sling Sling for removing rotor head. Blades should not be installed when rotor head is being removed. Picture shows sling in use.If you are using the guide and mast thread protector a longer strap is required. Let us know if you are using the thread protector... MSRP: Was: Now: $310.00 Add to Cart
407 Main Rotor 1-1/4" Mast Nut Socket 1-1/4 impact socket for the Main Rotor Mast Nut. 3/4" and 1" drive available MSRP: Was: Now: $68.00 - $80.00 Choose Options
407 Transmission Cover And Lift Plate Cover plates for the 407 transmissions. Fitted with eye for lifting transmission. NOT for lifting aircraft.​Lifting eye is rated for 9000 lbs Bell P/N T103314 MSRP: Was: Now: $390.00 Add to Cart
Bell 407 Tail Boom/Fuselage Former Ring Fixture Used for replacing tailboom/fuselage former ring or tail boom attach fittings on the Bell 407 only.The top two holes are larger than the 206. This fixture comes with 2 drill bushings. One for the top holes and one for the bottom holes. A 3/16... MSRP: Was: Now: $900.00 Add to Cart
407 Freewheeling Assembly Lip Seal R&R Work Aids to remove and install the lip seal on the freewheeling assembly nut Work Aids 7 & 8 from the Freewheeling Tools & Work Aids Chapter MSRP: Was: Now: $225.00 Add to Cart
407 Tail Rotor Gearbox Output Seal Work Aid Install or remove the tail rotor gearbox output seal. MSRP: Was: Now: $185.00 Add to Cart
407 Swashplate Overhaul Work Aids - 23pcs set ​Consists of 23 pieces for overhaul of the 407 swashplate as per CR&O MSRP: Was: Now: $50.00 - $2,385.00 Choose Options
407 Main Rotor Hub Assembly/Dis-assembly Work Aid - 5pcs set Contact us for individual piece pricingWork aid for assembly and dis-assembly of the mainrotor hub. Fig 62-4 Items 3, 8, 9, 10 MSRP: Was: Now: $950.00 Add to Cart
407 Mast Assembly Overhaul Work Aid #3 As title says, work aid for CR&O of Mast Assembly. Located in fig 63-2 item 3. 2" tall 5" diameter. MSRP: Was: Now: $410.00 Add to Cart
407 Tail Rotor Gearbox Input Wear Sleeve Installer - 2pcs set Tail rotor gearbox input wear sleeve installer MSRP: Was: Now: $135.00 Add to Cart
407 Tail Rotor Gearbox Input Lip Seal Work Aids Tail Rotor Gearbox Input Lip Seal Remover and Installer Work Aid #1 & #2 MSRP: Was: Now: $75.00 - $150.00 Choose Options
RR250 C30/C47 Compressor/Diffuser Orifice R&R Work Aid Use this work aid to remove and re-install the orifice when it is located in the exhaust collector.Good on any 206L with C30 installed, 407, and Sikorsky S-76A. MSRP: Was: Now: $85.00 Add to Cart
407 Main Rotor Mast Nut Torque Kit This kit includes everything you need to torque the mast nut on the 407 main rotor except for the 600 lb torque wrench. It has a 3-1 torque multiplier (3/4" drive), the torque reactor pin to hold a back up and the 1 1/4" 1 inch drive impact socket.​It... MSRP: Was: Now: $1,730.00 Add to Cart
407 Main Rotor Mast Nut Torque Kit With Torque Wrench This kit includes everything you need to torque the mast nut on the 407 main rotor including the 600 lb torque wrench made by Performance Tool. These are very good quality wrenches. It has a 3-1 torque multiplier, the torque reactor pin to hold... MSRP: Was: Now: $2,850.00 - $4,450.00 Choose Options
Rolls-Royce 250 C47 Engine Gearbox Drain As you know, the C47 has the quick disconnect chip detectors that have the self plugging housing. Unlike the C30's that will drain when you pull the chip detectors, the C47 requires this work aid to drain the gearbox. This drain is made from steel. MSRP: Was: Now: $105.00 Add to Cart
Rolls-Royce 250 HMU "Fuel Control" Throttle/Fly Detent Rigging Pin Easy to handle rigging pin with red streamer. MSRP: Was: Now: $45.00 Add to Cart
Air Conditioner Belt Tensiometer Belt Tensiometer specified by Bell for checking air conditioning belt tension. Scale reads in pounds and kilograms Measures tension from 30 to 160 lb., and 15 to 75 kg. Die-cast aluminum body, nylon indicator arm and pressure pad Fits in pocket... MSRP: Was: Now: $30.00 Add to Cart
Rolls-Royce 250 Oil Pressure Regulator Socket 1/4 inch drive socket for adjusting the oil pressure regulator.Makes it easy to adjust and count the turns plus it won't eat up the regulator adjusting bar when using needle nose pliers like other people used to do. MSRP: Was: Now: $45.00 Add to Cart
Rolls-Royce 250 Turbine Wheel Lock Used to lock the turbine wheel in place when installing the turbine section. The plate and rod are made from brass. The brass rod is soft enough to bend if necessary so it won't damage the turbine blades should excessive pressure be applied to the... MSRP: Was: Now: $65.00 Add to Cart
407 Tail Rotor Gearbox Wrench 407 tail rotor gearbox wrench to properly torque the aft left hand nut. MSRP: Was: Now: $75.00 Add to Cart
206L/407/429 CORDLESS Portable Hydraulic Pump Drive Unit Remove the hydraulic pump from the transmission with the hoses still connected and bolt hydraulic pump to the red pump pressure supply. The Cordless Makita is driven by a soft start, 5 speed, variable speed drive. You can finally lay to... MSRP: Was: Now: $4,900.00 Add to Cart
Honeywell HTS900 NP Sensor Shimming Work Aid Used for shimming the NP Sensor. Screw the large piece, adapter or bushing or whatever you want to call it into the gearbox. Screw in the center bolt until it contacts the gear tooth.​Lock it down using the knurled nut... MSRP: Was: Now: $245.00 Add to Cart
407/429 Main Rotor Blade Sling Main rotor blade sling aids in safely removing and installing main rotor blades. The 429 puts you at the upper limits of safely removing and replacing the main rotor blades due to the height of the blades, your work stands, and short mechanics. Even a... MSRP: Was: Now: $2,100.00 Add to Cart
407 Transmission Oil Filler Cap Removal Wrench Color varies when manufactured This little jewel makes removing and installing the xsmn oil filler cap a piece of cake.Every cap I have seen is difficult to remove and replace due to the swelling of the o'ring.This gives you the... MSRP: Was: Now: $45.00 Add to Cart
RR250-C30/C47 Spur Adapter Gear O'ring Installation Work Aid For engines C30 and C47 only RR P/N 23006785 MSRP: Was: Now: $410.00 Add to Cart
407 HTS900 Engine Oil Filter Socket & Wrench This socket removes the oil filter housing on the HTS900 engine.​Socket is removed with a 3/4" flex ratcheting box end wrench. We have the wrench if you don't have the flex style which makes it much easier to get on the attached nut. MSRP: Was: Now: $35.00 - $95.00 Choose Options
Oil Can Opener One Black Plastic "Church Key" FOD Free Turbine Oil Can Opener MSRP: Was: Now: $7.00 Add to Cart
407 Swashplate Shipping Plate Color varies when manufactured Protects swashplate and uniball from getting bounced around and beat up during shipping. MSRP: Was: Now: $55.00 Add to Cart
407 Hydraulic Pump Spline Wear Pins 407 Hydraulic pump splines wear pins .0200" (x2) & .0400" (x2) Click here for a selection of different size pins MSRP: Was: Now: $40.00 Add to Cart
Rolls-Royce 250 Starter/Generator Seal Installer & Fuel Pump Seal Installer - 2pcs This work aid is a 2 in 1. Use it on either the starter/generator seal or the fuel pump seal. Simplifies installation of seals and removes chances of damaging seal while installing. This work aid is only for lip seal (23079054). MSRP: Was: Now: $145.00 Add to Cart
ENGWASH-HF-BRACKET This is just the brackets and fasterners necessary to attach your (ENGWASHx2) double engine wash bottle set up to a Harbor Fright Welding Cart. Purchase your own Welding Cart from Harbor Freight and use these brackets to fasten them to the... MSRP: Was: Now: $300.00 Add to Cart
206/407/505 Tail Rotor Gearbox Input/Output Bearing Retaining Nut Wrench Used to apply torque to the input bearing retaining nut and the output bearing retaining nut. T101512 206-TRGB-F-04 MSRP: Was: Now: $425.00 Add to Cart
407 Mast Bearing Work Aid P/N 407MBR-HT Used to remove the bearing from the mast assembly. T103318-101 407-MAST-OH-03 MSRP: Was: Now: $550.00 Add to Cart
407 Torque Multiplier Fixture P/N 407TMF-HT Used with your choice of a 4-1 or 3-1 torque multiplier. Let the torque multiplier bump up against the pin to hold backup.This fixture lets you do the mast nut torque or 1-5 hr torque check by yourself not to mention... MSRP: Was: Now: $880.00 Add to Cart
407 Tailrotor Gearbox Quill Wrench Used to remove, install or torque the nut from the tail rotor gearbox quills. T101449 407-TRGB-F-05 407-XMSN-F-03 MSRP: Was: Now: $630.00 Add to Cart
206/407/505 Freewheeling Unit Wrench Used to remove and install the 214-040-241 nut. This tool replaces wrench assembly 407-240-006-101. 206-FWU-OH-18 T101960 MSRP: Was: Now: $150.00 Add to Cart
206/505/407 Freewheeling Unit Duplex Bearing Removal Driver Used to remove the 406-040-531 bearing from the 406-040-508 Cap Assembly. 206-FWU-OH-15 T103324-101 MSRP: Was: Now: $250.00 Add to Cart
206/407/505 Freewheeling Unit Bearing Installation Sleeve Used to install the 206-040-206 bearing into the 406-040-516 shaft. 206-FWU-OH-17 T103333 MSRP: Was: Now: $90.00 Add to Cart
206/407/505 Freewheeling Unit Shaft Removal Work Aids Used in conjuction with a press to remove the shaft from the bearing. T103310-101 MSRP: Was: Now: $150.00 - $450.00 Choose Options
C30/47 #1 Bearing in Compressor Puller C30/47 #1 Bearing in Compressor Puller 23005023 MSRP: Was: Now: $850.00 Add to Cart
206/407/505 Tail Rotor Output Shaft Nut Work Aid Used to apply torque to and remove the output shaft inner nut. T101513 206-TRGB-OH-05 MSRP: Was: Now: $250.00 Add to Cart
407 Trim Tab Bender Used to make adjustments on main rotor trim tabs during tracking. Comes with protective case. Bell P/N T103316 & T103317 MSRP: Was: Now: $2,300.00 Add to Cart
407 Mast Assembly Nut Wrench Wrench is used to remove and torque the nut on the mast assembly bearing during overhaul. 407-240-007-101/105 407-240-007-105 407-MAST-02 MSRP: Was: Now: $1,300.00 Add to Cart
407 Freewheeling Unit Nut Wrench Used to install the freewheel nut 407-FWU-OH-21 407-240-006 MSRP: Was: Now: $1,980.00 Add to Cart
407 Transmission Input Pinion Assembly And Removal Adapter Used in conjunction with a puller to remove and install the transmission pinion assembly Helitools 407-XMSN-OH-02 Bell 407-240-003 MSRP: Was: Now: $300.00 Add to Cart
407 Tail Rotor Drive Shaft Balancing Oil Reservoir Attachment Bracket Oil Reservoir attachment bracket for the sensor so you can balance the #1 tail rotor driveshaft. MSRP: Was: Now: $85.00 Add to Cart
