206/407/505 Freewheeling Unit Shaft Removal Work Aids MSRP: Was: Now: $150.00 - $450.00 Choose Options
407 Tail Rotor Drive Shaft Balancing Oil Reservoir Attachment Bracket MSRP: Was: Now: $85.00 Add to Cart
206/505 Transmission Bearing Installation and Removal Plug P/N 206XBS-HT Used to support the input driven spiral bevel gearshaft duplex bearing by the outer race while pressing bearing into or out of the transmission lower case. T101503 206-XMSN-OH-25 MSRP: Was: Now: $725.00 Add to Cart
206/505 Transmission Gear Shaft Nut Wrench Used to apply torque to the input driven spiral bevel gearshaft duplex bearing outer ring retaining nut. Bell P/N T101502 Helitools' P/N 206-XMSN-OH-03 MSRP: Was: Now: $225.00 Add to Cart
206/505 Mast Holding Fixture Used to hold the mast assembly when torque is applied to the ball bearing retaining nut during removal and installation. Bell P/N 206-240-002-101 Helitools P/N 206-MAST-F-05 CLICK HERE FOR T101499 MSRP: Was: Now: $850.00 Add to Cart
407 Mast Bearing Work Aid P/N 407MBR-HT Used to remove the bearing from the mast assembly. T103318-101 407-MAST-OH-03 MSRP: Was: Now: $550.00 Add to Cart
407 Torque Multiplier Fixture P/N 407TMF-HT Used with your choice of a 4-1 or 3-1 torque multiplier. Let the torque multiplier bump up against the pin to hold backup.This fixture lets you do the mast nut torque or 1-5 hr torque check by yourself not to mention... MSRP: Was: Now: $880.00 Add to Cart
206/505 Trunnion Hex Screw Wrench Used to torque hex insert screw in trunnion/pillow block. 206-MR-OH-18 MSRP: Was: Now: $96.00 Add to Cart
206 & 505 Main Rotor Blade Alignment Pins - 2pcs Easier and faster than mirrors and cheaper than a laser.No calibration needed. Drop it in the bolt hole and set the string. 206-MR-F-06 MSRP: Was: Now: $115.00 - $145.00 Choose Options
407 Tailrotor Gearbox Quill Wrench Used to remove, install or torque the nut from the tail rotor gearbox quills. T101449 407-TRGB-F-05 407-XMSN-F-03 MSRP: Was: Now: $630.00 Add to Cart
Rolls-Royce 250 PTO Seal Remover Used to remove single lip PTO seal on RR250 engines. Thread into the seal and use slide hammer to remove. MSRP: Was: Now: $525.00 Add to Cart
206 Planetary Shaft Sleeve Used to remove aand install the planet gear shaft from and into the arm of the spider and the bearing assembly inner race. T101506 206-XMSN-OH-20 MSRP: Was: Now: $525.00 Add to Cart
AS350 Flange Lock Wrench Has 2 sets of bolt patterns to fit Main Gearbox Input Flange, Brake Disc, Tail Rotor Gearbox Input Flange, and Engine Flanges. 350A93-3205-00 MSRP: Was: Now: $50.00 Add to Cart
206L Cyclic Servo Bellcrank Work Aid Work Aid acquired through purchase of HeliTools inventory. Something to do with setting of Cyclic Servo Bellcrank on the roof/deck. If you know, let us know exactly how it works so we can update this description. 206-FC-F-04L MSRP: Was: Now: $45.00 Add to Cart
206/505 Tail Rotor Rigging Flap Lock Work Aid Bell designed flap lock for 206/505. These were acquired through purchase of HeliTools inventory. Limited supply. See our design here. MSRP: Was: Now: $25.00 Add to Cart
412 Damper Bearing Set from Bridge Assembly Removal Work Aid To facilitate the removal of the Damper Bearing set from bridge assembly. MSRP: Was: Now: $55.00 Add to Cart
206/407/505 Freewheeling Unit Wrench Used to remove and install the 214-040-241 nut. This tool replaces wrench assembly 407-240-006-101. 206-FWU-OH-18 T101960 MSRP: Was: Now: $150.00 Add to Cart
206/505/407 Freewheeling Unit Duplex Bearing Removal Driver Used to remove the 406-040-531 bearing from the 406-040-508 Cap Assembly. 206-FWU-OH-15 T103324-101 MSRP: Was: Now: $250.00 Add to Cart
206/407/505 Freewheeling Unit Bearing Installation Sleeve Used to install the 206-040-206 bearing into the 406-040-516 shaft. 206-FWU-OH-17 T103333 MSRP: Was: Now: $90.00 Add to Cart
222 Tail Rotor Gearbox Holder Fixture to hold Tail Rotor Gearbox. 222-TRGB-OH-01 222-TRGB-OH-1B T103036 MSRP: Was: Now: $230.00 Add to Cart
222 Tail Rotor Gearbox Locknut Wrench Used to remove, install and torque locknut on Tail Rotor Gearbox. 222-TRGB-F-02 222-230-TRGB-F-01 T103134 MSRP: Was: Now: $190.00 Add to Cart
206/407/505 Freewheeling Unit Shaft Removal Work Aids Used in conjuction with a press to remove the shaft from the bearing. T103310-101 MSRP: Was: Now: $150.00 - $450.00 Choose Options
429 PW207 Mag Seal Puller Slide Hammer used to remove Seal P/N 3058291-01 PWC64888 PWC64888-1 Designed with customer to fit tighter than PWC factory workaid. All 3 lips engage. MSRP: Was: Now: $525.00 Add to Cart
C30/47 #1 Bearing in Compressor Puller C30/47 #1 Bearing in Compressor Puller 23005023 MSRP: Was: Now: $850.00 Add to Cart
Oil Collector Pan - Alignment Pilot Workaid Oil Collector Pan - Alignment Pilot Workaid for top case 206-040-550 Figure 63-19 MSRP: Was: Now: $250.00 Add to Cart
Oil Collector Pan - Alignment Pilot Work aid Oil Collector Pan - Alignment Pilot Work aid for top case 206-040-532 Figure 63-19 MSRP: Was: Now: $250.00 Add to Cart
Oil Collector Pan - Alignment Pilot Work Aid Set Oil Collector Pan - Alignment Pilot Work Aid Set For top case 206-040-550 & 206-040-532 Figure 63-19 MSRP: Was: Now: $450.00 Add to Cart
206/407/505 Tail Rotor Output Shaft Nut Work Aid Used to apply torque to and remove the output shaft inner nut. T101513 206-TRGB-OH-05 MSRP: Was: Now: $250.00 Add to Cart
206/505 Tail Rotor Gearbox Backlash Work Aid Used to hold output shaft so you can check the backlash between the tail rotor gearbox input pinion gear and output bevel gear. T102093 206-TRGB-OH-06 MSRP: Was: Now: $450.00 Add to Cart
407 Trim Tab Bender Used to make adjustments on main rotor trim tabs during tracking. Comes with protective case. Bell P/N T103316 & T103317 MSRP: Was: Now: $2,300.00 Add to Cart
407 Mast Assembly Nut Wrench Wrench is used to remove and torque the nut on the mast assembly bearing during overhaul. 407-240-007-101/105 407-240-007-105 407-MAST-02 MSRP: Was: Now: $1,300.00 Add to Cart
205/212/214/412 External Spline Wrench 205/212/214/412 External Spline Wrench 412-XMSN-OH-01 T101306 MSRP: Was: Now: $1,050.00 Add to Cart
206 Collective Low Position Rigging Work Aid Used to set the low collective position (2.40 inches) during rigging as required by the maintenance manual. 206-FC-F-01 MSRP: Was: Now: $20.00 Add to Cart
206 Tail Rotor Bearing Installation Used in conjuction with a hydralic press to push out the bearing from the side of the blade that has the swaged lip. MSRP: Was: Now: $375.00 Add to Cart
Bell 505 Portable Hydraulic Pump Drive Unit Portable Hydraulic Pressure Drive Unit for Bell 505. Due to the tight work space where the hydraulic pump is located, the unit comes with hydraulic hoses to be able to remove the hyd pump from the aircraft and move it away from the tight work area... MSRP: Was: Now: $4,750.00 Add to Cart
407 Freewheeling Unit Nut Wrench Used to install the freewheel nut 407-FWU-OH-21 407-240-006 MSRP: Was: Now: $1,980.00 Add to Cart
204/205/210/212/412 Grease Coupling Gauge A customer was looking through some old Army magazines and found this tool and sent to us. It is for the Bell 204, 205, 210, 212, some early models of 412 & Huey series aircraft. MSRP: Was: Now: $150.00 Add to Cart
407 Transmission Input Pinion Assembly And Removal Adapter Used in conjunction with a puller to remove and install the transmission pinion assembly Helitools 407-XMSN-OH-02 Bell 407-240-003 MSRP: Was: Now: $300.00 Add to Cart
Bell 505 CORDLESS Portable Hydraulic Pump Drive Unit Portable CORDLESS Hydraulic Pressure Drive Unit for Bell 505. Due to the tight work space where the hydraulic pump is located, the unit comes with hydraulic hoses to be able to remove the hyd pump from the aircraft and move it away from... MSRP: Was: Now: $4,900.00 Add to Cart
206B/L/505 Main Rotor Static Balance Kit Static Balancing Kit for 206B/L and 505. Comes in protective case with extra plastic bin to store lead weights. This is from Chuck Dugan from Helitools. We acquired his inventory. Contact us for any other tools that was previously supplied by... MSRP: Was: Now: $4,900.00 Add to Cart
407 Tail Rotor Drive Shaft Balancing Oil Reservoir Attachment Bracket Oil Reservoir attachment bracket for the sensor so you can balance the #1 tail rotor driveshaft. MSRP: Was: Now: $85.00 Add to Cart
