1/4" Drive - 12 point Universal/Swivel Sockets SAE & METRIC MSRP: Was: Now: $60.00 - $85.00 Choose Options
206/407/505 Swashplate Roll Stake Bearing Work Aid Kit MSRP: Was: Now: $250.00 - $3,000.00 Choose Options
Rolls-Royce 250-C20 Starter/Generator & Fuel Pump Seal Installer MSRP: Was: Now: $135.00 - $165.00 Choose Options
UV Flashlight for Transmission and Engine Oil Leak Checks UV flashlight for detecting oil leaks. Works great in the daytime (with cowlings on), works even better at night. Make sure you wash off your aircraft well before performing a ground run leak check with this light. It will light up ALL your residual oil... MSRP: Was: Now: $30.00 Add to Cart
1/4" Drive - 12 point Universal/Swivel Sockets SAE & METRIC We have located some quality swivel sockets at an affordable price that we are happy to offer here! They are made by Genius Tools. SAE (6pc) set consists of 1/4", 5/16", 3/8", 7/16", 1/2", & 9/16" Metric (9pc) set consists of 6mm, 7mm, 8mm, 9mm,... MSRP: Was: Now: $60.00 - $85.00 Choose Options
206 Main Rotor Grip Seal Holder For Purging Grease This work aid is for providing backup to the seal while purging the head of grease. MSRP: Was: Now: $55.00 Add to Cart
206 Main Rotor Grease Catch Bottle Adapter Here is a tool that you will love. It turns a plastic bottle into a grease receptacle when you are purging the grip. Once you are finished, just throw away the bottle. Keeps from making a huge mess on top of the aircraft. No wiping/smearing needed... MSRP: Was: Now: $15.00 Add to Cart
Rolls-Royce C30 Bleed Valve Wrench C30 Bleed Valve Wrench. This was designed for the MD500 guys who are working in a much tighter space than the 206 guys. MSRP: Was: Now: $120.00 Add to Cart
Kaflex Drive Shaft Protective Maintenance Cover Place this pad on the kaflex shaft during maintenance or when removed to protect it from dings and scratches. There are 2 options: 206 and 407. The 206 is a bit longer than the 407. Kaflex definitely not included for this price. MSRP: Was: Now: $50.00 Choose Options
206/407/505 Swashplate Roll Stake Bearing Work Aid Kit Bearing staking tool for the swashplate bearings. Allows you to perform the maintenance on the aircraft without removing the swashplate. T101530 MSRP: Was: Now: $250.00 - $3,000.00 Choose Options
Ultimate Swing Wrench Kit Ultimate Swing Wrench Kits contains 28 pieces. They are: T-handle, Screwdriver handle, and curved handle Open End: 1/4, 5/16, 3/8, 7/16, 1/2, & 9/16 Ratcheting Open End: 5/16 Regular Box End: 1/4, 5/16, 3/8, 7/16, 1/2, & 9/16 Ratcheting Box End:... MSRP: Was: Now: $1,750.00 Add to Cart
Spring Scale 0-50lbs 0-50 lbs Spring Scale. This spring scale is made of brass and will not shatter in your tool box like the cheap plastic spring scales. I've used both, brass and the plastic case spring scales. They both work. I just prefer the brass since they are a... MSRP: Was: Now: $110.00 Add to Cart
Rolls-Royce 250 Fuel Nozzle Holding Fixture Another one where the name of the tool describes it beautifully. Rolls-Royce P/N 6897875 MSRP: Was: Now: $690.00 Add to Cart
206 Greased Driveshaft Grease Applicator This is for the unfortunate souls that still have to pack grease into the older style greased driveshafts. If you have a Kaflex driveshaft, this won't work for you, but we will absolutely still sell it to you. You can make it into a cool key ring and... MSRP: Was: Now: $10.00 Add to Cart
206/407/429/505 Adapter Wrench 206L - Freewheeling Unit 407 - Freewheeling Unit 429 - Clutch Assembly 505 - Transmission Input Seal Bell P/N T103306 MSRP: Was: Now: $335.00 Add to Cart
206 Trim Tab Bender Used to bend the trim tabs during track & balance. MSRP: Was: Now: $1,500.00 Add to Cart
206 & 407 Tail Boom Support Stand 206 & 407 Tailboom Support StandThe tailboom can be removed or installed on the aircraft by one person with this stand.This stand is designed for high skid aircraft. If you have a low skid aircraft contact us so we can modify it for your low skids. MSRP: Was: Now: $3,500.00 Add to Cart
Dykem Cross Check Torque Stripe We have this torque stripe in orange only MSRP: Was: Now: $10.00 Add to Cart
206/407 Intake Plugs and Exhaust Cover Intake plugs come with pitot cover attached together. Your pilot will have to lose the plugs to be able to lose the pitot cover. MSRP: Was: Now: $408.00 - $450.00 Choose Options
RR250 C20/30/47 Engine Sled Made to fit the C20/C30/C47. Easy assembly and disassembly for shipping. Rolls-Royce P/N 6891189 MSRP: Was: Now: $900.00 Add to Cart
.020" Spherical Inspection Probe This is the spherical radius probe the maintenance manual calls for. This probe has a .020 spherical ball on the very end so that you can run it across the shaft splines to check for damage. Use it on: Multiple 206 items not listed... MSRP: Was: Now: $90.00 Add to Cart
206L Elevator Rigging Work Aid Requested by a mechanic, this T-bar is offset 6.5 degrees at the very end. You can use a fancy digital protactor to set the elevator angle, or you can get this easy to use, permanently set angle T-bar, that won't fluctuate readings on top of a helicopter... MSRP: Was: Now: $90.00 Add to Cart
206/407 Airframe Fuel Filter Fixture Requested by a customer, this is a fixture to hold the Airframe Fuel Filter in a vice. Has 4 tabs on it, so you can put the filter in a position that makes it easier for you to work on. MSRP: Was: Now: $85.00 Add to Cart
206A/B Cyclic Bell-Crank Rigging Work Aid Work Aid to help rig the 3.09 inches from roof deck to the center of bolt on the cyclic bell-crank. MSRP: Was: Now: $35.00 Add to Cart
206L Tail Rotor Rigging Go/No-Go Gauge Use this Go/No-Go Gauge to set the 1.46" on the bellcrank at the bottom of the vertical tunnel (broom closet) during tail rotor rigging. Helitools 206-FC-F-07 MSRP: Was: Now: $45.00 Add to Cart
RR250 Accessory Drive Lip Seal Installs the Starter/Generator and HMU (Fuel Pump) seals on the C47 gearbox MSRP: Was: Now: $140.00 Add to Cart
Engine Wash Bottle SINGLE BOTTLE: This is a stainless, 2 1/2 gallon bottle that has been used by all the major operators in the Gulf of Mexico for the last 45 years to my knowledge. I have replaced the short stock hose with 7 ft of high quality chemical resistant... MSRP: Was: Now: $325.00 - $815.00 Choose Options
206 Mainrotor Head Sling Sling has a clear vinyl coating on the 1/4" cables. Cables are 6 feet long.Hooks have safety latches. Cable comes with inspection tag, serialized and weight certification.Included is a Certificate of Compliance/TestCable is rated at 2200 lbs. Each leg... MSRP: Was: Now: $210.00 Add to Cart
206/407 Oil Cooler Blower Shaft Spline Wear Pins These are used to measure the wear on the oil cooler blower drive shaft splines. You get 2 each 0.1080" pins and 2 ea 0.1200" pins Click here for a selection of different size pins MSRP: Was: Now: $40.00 Add to Cart
206 Lifting Clevis Lifting clevis for the 206 series (and now the 505). 204-011-178-001 MSRP: Was: Now: $1,850.00 Add to Cart
Rolls-Royce 250 Fuel Nozzle Shimming Gauge The simplest gauge for calculating the required shims for the fuel nozzle! We provide instructions that are for reference, but as usual, refer to maintenance manual for latest information. We also have an excel spreadsheet to make... MSRP: Was: Now: $275.00 - $370.00 Choose Options
Bell 206 Transmission Cover and Lift Plate Cover plates for the 206 transmissions. Fitted with eye for lifting transmission. NOT for lifting aircraft.Lifting eye is rated for 9000 lbs MSRP: Was: Now: $290.00 Choose Options
Rolls-Royce 250 C20 Compressor Case Half Wrenches - 3pcs set With these wrenches, you can now cut down the time it takes to disassemble the case halves by 50%. Bits are removable which allows you to use the reverse side of the ratchet for removal and installation with just our two ratcheting wrenches. Comes with a... MSRP: Was: Now: $540.00 Add to Cart
Rolls-Royce 250 C20 Gearbox Seal Installer Installs the gearbox seals on the C20's. Place guide on output shaft, place seal over the guide, and place flange over the seal. MSRP: Was: Now: $300.00 Add to Cart
204/205/206/212/505 Pitch Horn Spreader Use it to spread the pitch horn and remove the trunnion fittings as per Bell Maintenance Manual. MSRP: Was: Now: $135.00 Add to Cart
Rolls-Royce 250 Turbine To Gearbox Attach Bolt Wrenches - 3pcs No longer will you need to use that calibrated elbow. We have designed 3 wrenches to perform the torque checks on the 6 turbine to gearbox attach bolts on the RR250-C30 and C47 engines. A long 1/4" extension will be required to torque the bolt above the... MSRP: Was: Now: $120.00 Add to Cart
Rolls-Royce 250 C30/C47 Fuel Nozzle Wrench This fuel nozzle wrench is double sided to give you better access to the fuel nozzle. With the cowling installed, if you place the wrench on the fuel nozzle, it may not sit the way you want because of the limited space, flip it to the other side. The... MSRP: Was: Now: $125.00 Add to Cart
Rolls-Royce 250 C30/C47 Medium Fuel Nozzle Wrench This wrench is usually preferred by the overhaul guys working the engine on a stand. MSRP: Was: Now: $95.00 Add to Cart
206/505 Blade Pin Press No longer will you need to waste time with a stuck pin. Once you decide the pin is stuck, place the pin press around the grip with the large hole around the top of the pin. (The tool is upside down in the pictures) Reinstall the bottom plate (the... MSRP: Was: Now: $725.00 Add to Cart
206/505 Bell Control Tube Trammel Accurate, simple trammel for the 206B, L and 505 main rotor pitch change links. This trammel will outperform other universal trammels. MSRP: Was: Now: $555.00 Add to Cart
206/505 Grip Lock Bolt - 2pcs Set Simplest, fastest, and best work aid to keep from scrapping a pair of TT Straps. Stronger and more reliable than T-handle type locks that most people use. MSRP: Was: Now: $78.00 Add to Cart
206B Bleed Valve Block Color varies when manufactured Bleed valve block for Rolls-Royce C20 engine with strap so that it can be hung. Rolls-Royce P/N 6886204 MSRP: Was: Now: $38.00 Add to Cart
Bolt Extractor This work aid lets you apply pressure to the bolt while applying penetrating lube. Once the bolt pops loose it can easily be removed. Pressure is applied to the bolt and not to the tail boom fitting. Cracked fittings require tail boom removal at lots of... MSRP: Was: Now: $225.00 Add to Cart
206 Mast Stand Adapter This adapter was made to fit inside of 2” galvanized pipe. Can be machined to fit in your stand. Please give us the size of the pipe you plan on using in the comments on checkout. If you need a mast stand for your 206L and don't have a scrap mast... MSRP: Was: Now: $230.00 Choose Options
206 Tail Rotor Rigging Work Aid Color varies when manufactured Made from PLA. Light and soft to protect tail rotor blades.Much lighter than the factory tool made from steel. Cheap enough you can purchase 2 pieces like Bell suggests in the maintenance manual to speed up the job. This... MSRP: Was: Now: $245.00 Choose Options
206/505 Series Main Rotor Grip Locks - 2pcs set These lock tight, won't slip and are used to adjust the grips level when aligning and static balancing the main rotor. MSRP: Was: Now: $205.00 Add to Cart
Rolls-Royce 250-C20/C30/C47 Engine Lifting Eye Engine lifting eye for C20, C30, and C47. Long enough to clear the exhaust stack so it doesn't have to be removed. Rolls-Royce C20 6796963Rolls-Royce C30/C47 6889888 MSRP: Was: Now: $475.00 Add to Cart
OH58 Main Transmission Drain This is the main gearbox drain hose for the OH58. Pull your chip plug where you want to drain the transmission and check to see if it is the long or short style. Also check to see if the drain has 3 pins or 3 slots for engaging and locking into... MSRP: Was: Now: $95.00 Add to Cart
206B Transmission Drain 206B transmission drain comes with a 7 ft hose.This drain is used when the chip plug has the 3 pins to engage and lock. MSRP: Was: Now: $95.00 Add to Cart
206B&L Tail Rotor Gearbox Drain Tail Rotor Gearbox Drain for the 206 series aircraft. Comes with 7 ft hose. MSRP: Was: Now: $95.00 Add to Cart
206L Transmission Drain Main transmission drain for the 206L series aircraft. Bell P/N: DB3188L MSRP: Was: Now: $95.00 Add to Cart
Slide Hammer Shorter than commercial slides to pop out fuel pump cartridges in the belly when there is little ground clearance available.Comes with 7/16 20 and a 1/4 28 thread adapters. MSRP: Was: Now: $90.00 Add to Cart
206 Tail Rotor Mast Nut Socket 206 series tail rotor retaining nut extended socket. MSRP: Was: Now: $95.00 Add to Cart
206 Series Tail Rotor Crosshead Remover Used to remove the tailrotor crosshead on Bell 206 series aircraft.Safer and faster than the 2 jaw pullers. MSRP: Was: Now: $295.00 Add to Cart
Bypass Spool Check Mount - With Dial Indicator Bracket held on with nylon screws so as not to damage the servo anodized surface.The bracket also comes with a powder coat finish which gives additional protection to the anodized finish on the servo. MSRP: Was: Now: $2.00 - $255.00 Choose Options
Rolls-Royce 250 Ignitor Wrench Ignitors can be hard to remove for several reasons. Someone put it in too tight, didn't use anti-seize or used a 12 point socket and slipped, rounding off the corners. This wrench is made from a 6 point impact socket. Install the wrench and put the... MSRP: Was: Now: $65.00 Add to Cart
Rolls-Royce 250 Starter/Generator Spline Turn Wrench T-handle wrench for turning the N1 wheels while doing maintenance on the RR250 series engines. Starter/generator splines are hard to find, so get yours here Rolls-Royce P/N 6799790 MSRP: Was: Now: $55.00 Add to Cart
206 & 407 Free Wheeling Unit Aft Flange Wrench Use this work aid by attaching it to the aft flange with two bolts. Use a breaker bar to keep shaft from rotating. Through the larger centered hole, use your socket to torque the nut. We can make the square drive hole 1/2in if you prefer. Bell P/N... MSRP: Was: Now: $85.00 Add to Cart
Reversible Swing Wrenches These reversible swing wrenches are an improvement over our other wrenches. We are using the reversible Gear wrench brand so when you get into a tight spot and can't get the wrench off the nut or bolt you can simply flip the reversing lever and back out... MSRP: Was: Now: $95.00 - $105.00 Choose Options
Brass Screwdriver For Compass Adjustment No more trying to make a screw driver for adjusting compasses with a hammer and welding rod.This is a quality, solid brass screwdriver made especially for adjusting compasses.It's 4 3/4 inches long and the blade tip is 5/32" wide. MSRP: Was: Now: $23.00 Add to Cart
206 Transmission Input Flange Wrench T101555 transmission input flange wrench for the 206. MSRP: Was: Now: $335.00 Add to Cart
206/407/505 Oil Cooler Blower Driveshaft Spanner Wrench Wrench to get off the spanner nut on the oil cooler blower. The L-model wrench will also work on the 407. MSRP: Was: Now: $70.00 Add to Cart
206 Oil Cooler Blower Driveshaft Spanner Socket A better fitting work aid to remove the oil cooler blower driveshaft spanner nut. MSRP: Was: Now: $310.00 Add to Cart
206 Air Conditioner Pulley Wrench This air conditioner pulley wrench avoids elongating the pin hole when using a pin spanner, plus it stays in place when torquing. MSRP: Was: Now: $135.00 Add to Cart
206 Tail Rotor Balance Wheel Adapter No longer will you have to use a flathead screwdriver and mallet to unscrew the balance wheel. Can also be used for torquing when the 1/4" drive cutouts on the balance wheels are worn and won't hold the torque wrench. MSRP: Was: Now: $40.00 Add to Cart
206 Knurl Nut Wrench This will easily remove that stuck knurl nut. It is especially great if you want to replace the knurl nut liner and don't want to ruin the knurl nut with channel locks because the knurl nut is frozen. MSRP: Was: Now: $130.00 Add to Cart
206 Tail Rotor Flap Stop Work Aid This item is 3D printed, made out of PLA. Color may vary. This work aid was designed to replace the Bell designed fork shaped lockout work aid. The 206 tail rotors are shimmed between the tailrotor hub and flap stop. That means every tailrotor is... MSRP: Was: Now: $195.00 Choose Options
Bell Rotor Brake Bleeder Kit Oil can comes with 6 feet of hose and allows bleeding the brakes to be a one man job. Fits most Bell models. Quickest way to bleed rotor brakes. MSRP: Was: Now: $38.00 - $168.00 Choose Options
KaFlex Compression Kit for 206L and 407 This is the easiest and fastest way to R&R 206L and 407 KaFlex shafts.Simply make 2 wraps on the driveshaft passing through the holes in the aluminum rods, tie a knot and twist the rods until the cord starts to tighten. Tighten just enough to slip... MSRP: Was: Now: $275.00 Add to Cart
Swing Wrenches Don't buy bulky swing wrenches from tool trucks made from the old ratcheting dog bone wrenches that were great 40 years ago. Ours are made with the slimmer profile Gearwrench ratcheting boxends. Rotor brakes, flight controls in the tailboom, or fuel... MSRP: Was: Now: $85.00 - $95.00 Choose Options
Bell 206B&L Mast Nut Socket This 7/8 - 3/4 drive socket has been bored out to fit properly on the mast nut. PD2734 MSRP: Was: Now: $68.00 Add to Cart
Rolls-Royce 250 Idle Adjustment Swing Wrench This swing wrench is made specifically for adjusting the idle on the 206 RR250 engine. Of course with that in mind, you can also use it for any tight spot that requires a 1/4" box end wrench. We have 2 types of swing wrenches. Our version and Helitools'... MSRP: Was: Now: $85.00 Choose Options
Rolls-Royce 250 Exhaust Stack Wrench Wrench is made for removal of the nuts on the exhaust stack. Keeps nuts from falling into crevices of the engine. MSRP: Was: Now: $30.00 Add to Cart
Composite Tap Hammer Use the tap hammer on main rotor blades or any other composite material to check for delamination. You can order somewhere else for $15 + $12 shipping ($27 total) or just bundle with your next order with us. Equivalent to T75449-2 MSRP: Was: Now: $24.00 Add to Cart
Grease Fitting - Straight These are the threaded ones, not the quick disconnect ones that get grease everywhere except the part you want it in. MSRP: Was: Now: $15.00 Add to Cart
Grease Fitting - 90° These are the threaded ones, not the quick disconnect ones that get grease everywhere except the part you want it in. MSRP: Was: Now: $20.00 Add to Cart
90° Grease Coupler I recently found this 90 degree grease coupler that works great on hard to access grease fittings.Works really well on the oil cooler blower bearings on the Bell 407. It slides in from the side when straight on access is difficult or next to impossible. MSRP: Was: Now: $16.00 Add to Cart
Jackscrews 1/4" 28 - 3pcs Use these on transmission input quills, freewheeling unit, tailrotor gearbox, or any component requiring 1/4" 28 jackscrews. T101308 MSRP: Was: Now: $75.00 Add to Cart
Rolls-Royce 250 C30/C47 Gearbox PTO Seal Installer This installer works on the C30 and C47 engines. You can install one seal at a time or both at once. This is the best seal installer you will find for the gearbox seals. MSRP: Was: Now: $825.00 Add to Cart
Rolls-Royce 250 C30/C47 Gearbox PTO Seal Remover Removes rear gearbox seal. MSRP: Was: Now: $725.00 Add to Cart
206 Main Rotor Blade Friction Pad Bonding Clamp Main rotor blade friction pad bonding clamp. Can do both the grip and the blade's friction pad MSRP: Was: Now: $145.00 Add to Cart
Rolls-Royce 250 C30/C47 Bleed Valve Shop Air Adapter Quick disconnect so that you can use shop air to close the Bleed valve. MSRP: Was: Now: $40.00 Add to Cart
Rolls-Royce 250 Quick Disconnect Coupling For Engine Rinse Name says it all. MSRP: Was: Now: $45.00 Add to Cart
Saft Battery Cap Pressure Tester This manifold is for pressure testing the saft battery caps. We will need you to send us the caps you want the manifold manufactured for. Pictured are two different battery caps. If the battery cap is a common thread, we can make the work aid with... MSRP: Was: Now: $250.00 Add to Cart
206L Tach Generator Driveshaft Removal & Installation Work Aid Work aid to remove and replace tach generator driveshaft as seen in figure 63-7c MSRP: Was: Now: $125.00 Add to Cart
206 Main Rotor Hub Pitch Horn Lock Use this work aid when lifting the hub assembly from the mast. Remove upperside of pitch control links and install the work aid. MSRP: Was: Now: $425.00 Add to Cart
206 Swashplate Uniball Lower Bushing Remover Removes lower bushings from swashplate uniball. MSRP: Was: Now: $55.00 Add to Cart
206 & 407 Tailboom Maintenance Stand 206 & 407 Tailboom Maintenance StandCall for more information.Maintains tailboom at chest level for maintenance. Able to rotate 360 degrees. MSRP: Was: Now: $0.00 Add to Cart
Rolls-Royce 250 Power Turbine Support Cleaning Kit Kit comes in a foam insert for easy storage and handling. Keep the cardboard box it comes in for added protection. RR P/N 23007615 MSRP: Was: Now: $175.00 Add to Cart
Torque Adapters 1/4" Drive Hard to find 1/4" drive torque adapters. Most torque adapters you will find are 3/8" drive. These will allow you to use that low torque 1/4" torque wrench without the 3/8" to 1/4" adapter. SAE: The standard set consists of 1/4", 5/16", 3/8", &... MSRP: Was: Now: $50.00 - $170.00 Choose Options
206 & 407 Transmission Oil Pump Puller Slide hammer for transmission oil pump on 206s and 407s. MSRP: Was: Now: $150.00 Add to Cart
206/407 Transmission Oil Pump & Housing Assembly Work Aid If you're looking for this, you already know what it's for. TB206L-05-218 TB407-05-65 MSRP: Was: Now: $135.00 Add to Cart
206/407 Hydraulic Pump Shaft Remover Work aid that helps easily remove the hydraulic pump shaft. You will no longer need to pry out the shaft with pliers and have the shaft and spring flying across the hangar, or worse, a grassy field. Open the shaft remover and place it around the... MSRP: Was: Now: $195.00 Add to Cart
RR250 C30/C47 Compressor/Diffuser Orifice R&R Work Aid Use this work aid to remove and re-install the orifice when it is located in the exhaust collector.Good on any 206L with C30 installed, 407, and Sikorsky S-76A. MSRP: Was: Now: $85.00 Add to Cart
Rolls-Royce 250-C20 Starter/Generator & Fuel Pump Seal Installer This is the new seal installer from Rolls-Royce's Commercial Service Letter. This was designed for installing the new lip seals (23091467) which include a supplied installation mandrel.Although it will also work on the old lip seals (23079054) we,... MSRP: Was: Now: $135.00 - $165.00 Choose Options
Air Conditioner Belt Tensiometer Belt Tensiometer specified by Bell for checking air conditioning belt tension. Scale reads in pounds and kilograms Measures tension from 30 to 160 lb., and 15 to 75 kg. Die-cast aluminum body, nylon indicator arm and pressure pad Fits in pocket... MSRP: Was: Now: $30.00 Add to Cart
Rolls-Royce 250 Oil Pressure Regulator Socket 1/4 inch drive socket for adjusting the oil pressure regulator.Makes it easy to adjust and count the turns plus it won't eat up the regulator adjusting bar when using needle nose pliers like other people used to do. MSRP: Was: Now: $45.00 Add to Cart
Rolls-Royce 250 Turbine Wheel Lock Used to lock the turbine wheel in place when installing the turbine section. The plate and rod are made from brass. The brass rod is soft enough to bend if necessary so it won't damage the turbine blades should excessive pressure be applied to the... MSRP: Was: Now: $65.00 Add to Cart
Rolls-Royce 250 St. Gobain PTO Seal Installer These are the seal installers for the new St Gobain seals p/n 23091293 (red) and p/n 23091353 (blue)They can also be used for installing the Viton SealsThe C20 and C30/47 have different seal insertion depths so order according to your engine model MSRP: Was: Now: $275.00 Choose Options
206L4 Kaflex Mounting Wrench 206L4 Kaflex Mounting WrenchIf you have ever installed a Kaflex drive shaft, you know how its practically impossible to actually torque them. We designed these wrenches so you could stop using that calibrated elbow and properly torque them with a torque... MSRP: Was: Now: $105.00 Add to Cart
