Shop by Make & Model

S70/UH-60 Landing Gear Strut Lower-Attach Bolt Wrench

Designed to be a better and tighter fit than a crowsfoot.   4920-01-554-9693 1006776

S70/UH-60 Landing Gear Strut Servicing Tower

S70/UH-60 Landing Gear Strut Servicing TowerCall For PriceThis 8' tower is designed to speed up the servicing of the strut by allowing you to work on the strut out in the open and not on an aircraft that is on jacks 4 feet in the air.

S58 Tail Rotor Gearbox Drain

BO105 Holding Jam Nut To Torque

Holding jam nut to torque or remove the main rotor hub studs on the bottom of the hub. Screw this on to the stud, hold a back up on the lower nut and tighten the bolt. Slide a socket over the large nut and torque to specs. 

BO105 Transmission Drain

BO105 Transmission Drain

BO105 Tail Rotor Gearbox Drain

BO105 Tailrotor Gearbox Drain

BK117 Tail Rotor Gearbox Drain

Tail rotor gearbox drain and hose

S76C Main Driveshaft Alignment Rod

Used to check the main drive shaft alignment when changing engine mounts or any time an alignment problem is suspected. Normally companies furnish this rod but too often it doesn't make it back to the right place in the tool crib so when you need it, it...

S92 Engine Oil Drain

We have the engine oil drain at a lot lower price than the manufacturer.

S92 Hydraulic Oil Drain

Twist Grip Drive Tube and Control Pinion Attachment Work Aid

Twist Grip Drive Tube and Control Pinion Attachment Work AidP/N: ASB76A006Used to check correct bonding strength of the control pinion on the pilot and copilot collective lever driver tubes.

M01 and M05 MODULE OIL DRAIN HOSE

Drain hose for the M01 and M05 modules. Comes with a 7 foot hose.

AS350 Engine Oil Drain

The AS350 engine oil and hydraulic oil tanks use the same drain.This drain comes with a 7 ft hose just like all the rest.

AS350 Tail Rotor Gearbox Drain

Not much to say here except that it comes with a 7 ft hose.Stick it in the hole and the oil runs out.

AS350 Transmission Oil Drain

Just like all the others except different.

AS350 Starter/Generator Seal Installer

Installs and seats the seal into the flange housing with air pressure. 8813824000

AS350 Swashplate Shimming Aid

For those of you familiar with shimming the AS350 series swashplate you've probably had to rent this before and know what it is. 350A93-3714-00

AS350 Flight Control Rigging Kit

Rent:  $200/Day - Rent starts upon arrival at your location   AirBus no longer offers this kit for rent.

AW109 Main Transmission Drain

This is for the 109 with the chip fuzz burner.

EC135 & EC145 Hydraulic Module Plunger Work Aid

This hydraulic module plunger work aid is designed for the aft facing hydraulic module on the 145 series aircraft. The older style plunger work aid is too large to fit between the transmission and hydraulic module. This work aid is required if you want...

EC135 Engine Oil Drain

Comes with a 7 ft. hose.

EC135 Transmission Drain

Comes with a 7 ft. hose.

EC135 Tail Rotor Gearbox Drain

Comes with a 7 ft. hose.

EC145 Transmission Oil Drain

Comes with a 7 ft. hose

EC145 Engine Oil Drain

Comes with a 7 ft. hose

EC145 Tail Rotor Gearbox Oil Drain

Comes with a 7 ft. hose

MD500 Tail Rotor Inner Feathering Bearing Removal

Removes the inner feathering bearings as per the component overhaul manualWe also have the installation work aid for the 369A1716-3, -5, -7, -9, -17, and -19 bearings 

MD500 Tail Rotor Pitch Bearing Installer

Specify which installer you need according to the bearing P/N's shown above.

MD500 Transmission Drain

Typical xsmn drain  with a 7 ft hose.

MD500 SWASHPLATE GREASE PLATE

Designed with 4 grease zerks to make greasing the swashplate quicker and easier than other work aids out there.

MD500 Main Rotor Upper Scissor Crank Bearing R&R

R&R main rotor scissor crank bearing without wasting time trying to find sockets and bolts to press the bearing in and out. ​It has been brought to my attention that after several bearings have been changed that the bore tends to...

MD500 Main Rotor Lower Scissor Crank Bearing R&R

R&R the lower scissor crank bearing. This consists of installer and remover for the lower scissor. Due to the tight outer ear we had to make a fitting to clear the curved edge when installing the bearing.Removal only requires the receiver and bolt.

MD500 Main Rotor Mast Nut Wrench

Main rotor mast nut wrench fits MD500 D,E,FAt least that's what we've been told. 369A9829

MD500 Main Rotor P/C Link Trammel

Adjustable trammel for the MD500 p/c links.  This may fit other MD products.One bolt is 5/16" and the opposite end is 1/4".Distance between bolts is about 6 3/8" with plenty of adjustment remaining.

Rolls-Royce RR300 Seal Installer

This is the new seal installer from Rolls-Royce's Commercial Service Letter. This was designed for installing the new lip seals (23091467) which include a supplied installation mandrel.

52 inches long X 14 inch Drive Extension

​This extension is to R&R the 2 AN-3's inside the tail boom that hold the support for the tail rotor driveshaft.​It comes with a 3/8" 12 point socket with a magnet inside to hold the bolts in place.You no longer need to use multiple...

Rolls-Royce 300 Aft PTO Seal Installer

Name describes it all.

Rolls-Royce 300 PTO Seal Remover

Name describes it all.

Robinson Teeterbar - R22 only

Robinson Teeterbar - R22 onlyP/N: HWAMT354-1

Robinson Teeterbar - R44 & R66

Robinson Teeterbar - R44 & R66​P/N: HWAMT354-4

Spindle Boot Plate

Robinson Spark Plug Ignition Cable Wrench

Robinson R22 Clutch Micro Switch Swing Wrenches

1/4 in box end with a 3/8 in open end swing wrench for adjusting the clutch micro switch.

Rolls-Royce 250 Oil Pressure Regulator Socket

1/4 inch drive socket for adjusting the oil pressure regulator.Makes it easy to adjust and count the turns plus it won't eat up the regulator adjusting bar when using needle nose pliers like other people used to do.

Rolls-Royce 250 Turbine Wheel Lock

Used to lock the turbine wheel in place when installing the turbine section. The plate and rod are made from brass. The brass rod is soft enough to bend if necessary so it won't damage the turbine blades should excessive pressure be applied to the...

Rolls-Royce 250 St. Gobain PTO Seal Installer

These are the seal installers for the new St Gobain seals p/n 23091293 (red) and p/n 23091353 (blue)They can also be used for installing the Viton SealsThe C20 and C30/47 have different seal insertion depths so order according to your engine model

407 Tail Rotor Gearbox Wrench

407 tail rotor gearbox wrench to properly torque the aft left hand nut.

206L4 Kaflex Mounting Wrench

206L4 Kaflex Mounting WrenchIf you have ever installed a Kaflex drive shaft, you know how its practically impossible to actually torque them. We designed these wrenches so you could stop using that calibrated elbow and properly torque them with a torque...

206A/B & TH-67 Bonded Coupling Tail Rotor Drive Shaft Wrench

Used to proof load test installed bonded tail rotor driveshafts to verify the integrity of the bond line. Two required as per ASB 206-20-139 issued 21 July 2020 Also used to comply with AD 2023–06–05

MD369/500 Tail Rotor Rigging Gauge

Color varies when manufactured 3D Printed, made from PLA. Gauge for rigging tail rotor on 369/500.

206L/407/429 CORDLESS Portable Hydraulic Pump Drive Unit

Remove the hydraulic pump from the transmission with the hoses still connected and bolt hydraulic pump to the red pump pressure supply. The Cordless Makita is driven by a soft start, 5 speed, variable speed drive. You can finally lay to...

Honeywell HTS900 NP Sensor Shimming Work Aid

Used for shimming the NP Sensor. Screw the large piece, adapter or bushing or whatever you want to call it into the gearbox.   Screw in the center bolt until it contacts the gear tooth.​Lock it down using the knurled nut...

429 Main Rotor Blade Sling

Main rotor blade sling aids in safely removing and installing main rotor blades. The 429 puts you at the upper limits of safely R&R the main rotor blades due to the hight of the blades, your work stands and short mechanics. Even a tall guy has to...

205/212 Blade Bolt Socket

Fits both the 205 and 212 blade bolt nut P/N 204-011-153-001

S70/UH-60 Tail Rotor Gear Box Drain

​Comes with 7 foot hose.

Blackhawk Door Storage Rack

This rack was made for the local guard unit. It holds up to 8 doors.Specify the number of door slots needed.

S92 Main Transmission Oil Drain

S92 main gear box oil drain with a 7 ft hose

S92 APU Oil Drain

APU gearbox drain with 7 ft hose

S92 Tailrotor Gearbox Oil Drain

S92 intermediate gearbox and tail rotor gearbox drains, 7 ft hose.

AS350 Flight Control Rigging Kit - DAILY RENTAL

Rent:  $200/Day - Rent starts upon arrival at your location   AirBus no longer offers this kit for rent.

407 Transmission Oil Filler Cap Removal Wrench

Color varies when manufactured This little jewel makes removing and installing the xsmn oil filler cap a piece of cake.Every cap I have seen is difficult to remove and replace due to the swelling of the o'ring.This gives you the...

MD Tail Rotor Nut Wrench

Tail Rotor Nut Wrench (MD29823-5A) for: MD500 MD500D MD500E MD520N MD530F   

Notar Fan Bearing Re-Greasing Disk

Robinson R22 & R44/R66 Rotor Head Bolt Stretch Gauge

Does not come with dial indicator.  Dial Indicator can be purchased separately by clicking here and selecting Dial Indicator in the drop down menu 

407 HTS900 Engine Oil Filter Socket & Wrench

This socket removes the oil filter housing on the HTS900 engine.​Socket is removed with a 3/4" flex ratcheting box end wrench. We have the wrench if you don't have the flex style which makes it much easier to get on the attached nut.

Oil Can Opener

One Black Plastic "Church Key" FOD Free Turbine Oil Can Opener

Bolt Removal Wrench

Clutch tool for MD F-model

407 Hydraulic Pump Spline Wear Pins

407 Hydraulic pump splines wear pins .0200" (x2) & .0400" (x2) Click here for a selection of different size pins

GE - CT-7 FUEL FILTER WRENCH

Ratcheting 5/8 - 3/8 drive wrench for R&R of fuel filter bowl on the GE CT-7 engine

429 PITCH LINK TENSION RELIEVER

429 PITCH LINK TENSION RELIEVER

S76 Brake Master Cylinder Bleeder Work Aid

S76 Brake Master Cylinder Bleeder Work Aid

ENGWASH-HF-BRACKET

This is just the brackets and fasterners necessary to attach your (ENGWASHx2) double engine wash bottle set up to a Harbor Fright Welding Cart.  Purchase your own Welding Cart from Harbor Freight and use these brackets to fasten them to the...

Swashplate Gimbal Ring Bolt Removal Workaid (204B, 205, 212 & 412)

Swashplate Gimbal Ring Bolt Removal Workaid (204B, 205, 212 & 412)   204B-22-27 205-22-45 205B-22-29 212-22-74 412-22-93

407 Torque Multiplier Fixture

P/N 407TMF-HT   Used with your choice of a 4-1 or 3-1 torque multiplier.  Let the torque multiplier bump up against the pin to hold backup.This fixture lets you do the mast nut torque or 1-5 hr torque check by yourself not to mention...

206 & 505 Main Rotor Blade Alignment Pins - 2pcs

Easier and faster than mirrors and cheaper than a laser.No calibration needed. Drop it in the bolt hole and set the string.   206-MR-F-06

Rolls-Royce 250 PTO Seal Remover

Used to remove single lip PTO seal on RR250 engines.   Thread into the seal and use slide hammer to remove.

AS350 Flange Lock Wrench

Has 2 sets of bolt patterns to fit Main Gearbox Input Flange, Brake Disc, Tail Rotor Gearbox Input Flange, and Engine Flanges.    350A93-3205-00

206L Cyclic Servo Bellcrank Work Aid

Work Aid acquired through purchase of HeliTools inventory. Something to do with setting of Cyclic Servo Bellcrank on the roof/deck. If you know, let us know exactly how it works so we can update this description.   206-FC-F-04L

206/505 Tail Rotor Rigging Flap Lock Work Aid

Bell designed flap lock for 206/505. These were acquired through purchase of HeliTools inventory. Limited supply.     See our design here.

412 Damper Bearing Set from Bridge Assembly Removal Work Aid

To facilitate the removal of the Damper Bearing set from bridge assembly.

429 PW207 Mag Seal Puller

Slide Hammer used to remove Seal P/N 3058291-01   PWC64888 PWC64888-1    Designed with customer to fit tighter than PWC factory workaid. All 3 lips engage. 

C30/47 #1 Bearing in Compressor Puller

C30/47 #1 Bearing in Compressor Puller   23005023

407 Trim Tab Bender

Used to make adjustments on main rotor trim tabs during tracking.  Comes with protective case.  Bell P/N T103316 & T103317

206 Collective Low Position Rigging Work Aid

Used to set the low collective position (2.40 inches) during rigging as required by the maintenance manual.   206-FC-F-01

Bell 505 Portable Hydraulic Pump Drive Unit

Portable Hydraulic Pressure Drive Unit for Bell 505. Due to the tight work space where the hydraulic pump is located, the unit comes with hydraulic hoses to be able to remove the hyd pump from the aircraft and move it away from the tight work area...

204/205/210/212/412 Grease Coupling Gauge

A customer was looking through some old Army magazines and found this tool and sent to us. It is for the Bell 204, 205, 210, 212, some early models of 412 & Huey series aircraft.

Bell 505 CORDLESS Portable Hydraulic Pump Drive Unit

Portable CORDLESS Hydraulic Pressure Drive Unit for Bell 505.  Due to the tight work space where the hydraulic pump is located, the unit comes with hydraulic hoses to be able to remove the hyd pump from the aircraft and move it away from...

206B/L/505 Main Rotor Static Balance Kit

Static Balancing Kit for 206B/L and 505. Comes in protective case with extra plastic bin to store lead weights. This is from Chuck Dugan from Helitools. We acquired his inventory. Contact us for any other tools that was previously supplied by...

407 Tail Rotor Drive Shaft Balancing Oil Reservoir Attachment Bracket

Oil Reservoir attachment bracket for the sensor so you can balance the #1 tail rotor driveshaft.