Shop by Make & Model

206/407/505 Swashplate Roll Stake Bearing Work Aid Kit

Bearing staking tool for the swashplate bearings. Allows you to perform the maintenance on the aircraft without removing the swashplate.   T101530

MD500 Collective Bungee Tool

I'll let the maintenance manual explain it: The collective bungee installation tool prevents rapid,uncontrolled movement of the collective which could damage the flight controls and cause injury to personnel. ST508

Spring Scale 0-50lbs

0-50 lbs Spring Scale.  This spring scale is made of brass and will not shatter in your tool box like the cheap plastic spring scales. I've used both, brass and the plastic case spring scales. They both work. I just prefer the brass since they are a...

206 Hydraulic Servo Rigging Pins

Rigging pins for the hydraulic servos. Bell P/N T102019

206 Trim Tab Bender

Used to bend the trim tabs during track & balance. 

206L Elevator Rigging Work Aid

Requested by a mechanic, this T-bar is offset 6.5 degrees at the very end. You can use a fancy digital protactor to set the elevator angle, or you can get this easy to use, permanently set angle T-bar, that won't fluctuate readings on top of a helicopter...

206A/B Cyclic Bell-Crank Rigging Work Aid

Work Aid to help rig the 3.09 inches from roof deck to the center of bolt on the cyclic bell-crank.

206L Tail Rotor Rigging Go/No-Go Gauge

Use this Go/No-Go Gauge to set the 1.46" on the bellcrank at the bottom of the vertical tunnel (broom closet) during tail rotor rigging. Helitools 206-FC-F-07

Bolt Extractor

This work aid lets you apply pressure to the bolt while applying penetrating lube. Once the bolt pops loose it can easily be removed. Pressure is applied to the bolt and not to the tail boom fitting. Cracked fittings require tail boom removal at lots of...

206 Series Tail Rotor Crosshead Remover

Used to remove the tailrotor crosshead on Bell 206 series aircraft.Safer and faster than the 2 jaw pullers.

Bypass Spool Check Mount - With Dial Indicator

Bracket held on with nylon screws so as not to damage the servo anodized surface.The bracket also comes with a powder coat finish which gives additional protection to the anodized finish on the servo.  

Swashplate Shim Alignment Studs

Holds the shims in position when doing the swashplate friction check. The hex head is 5/32" drive.An allen wrench is easier to get in to tight areas than a long phillips screwdriver. Can also be used as jack screws on the 206 and 407 transmission input...

206 Main Rotor Hub Pitch Horn Lock

Use this work aid when lifting the hub assembly from the mast. Remove upperside of pitch control links and install the work aid.

206 Swashplate Uniball Fixture

Supports lower portion of uniball when pressing in the lower bushings.

206 Swashplate Uniball Lower Bushing Remover

Removes lower bushings from swashplate uniball.

Torque Adapters 1/4" Drive

Hard to find 1/4" drive torque adapters. Most torque adapters you will find are 3/8" drive. These will allow you to use that low torque 1/4" torque wrench without the 3/8" to 1/4" adapter.   SAE: The standard set consists of 1/4", 5/16", 3/8", &...

407 Pitch Link Tension Reliever

Used to move the blade and grip when trying to re-connect the pitch change links.

407 Main Rotor Pitch Change Link Trammel

Trammel made especially for the 407 main rotor pitch change link. Trammel adjusts to fit the old link.Pull the round pin out and install the new link.Adjust the new link until the round pin slides back into the hole. Tighten the link jam nuts and...

407 Collective Pitch Transducer Work Aid

Work aid to help rig the collective pitch transducer.

407 Swashplate Overhaul - 23pcs set

​Consists of 23 pieces for overhaul of the 407 swashplate as per CR&O

429 Main Rotor Pitch Change Link Trammel

Accurate, simple trammel for the 429 main rotor pitch change links. This trammel will outperform other universal trammels.

429 Idler Link Bushing R&R

Remove and replace the ilder link bushings as per the maintenance manual.

429 Swashplate Shim Alignment Studs - 7pcs set

Holds the shims in position when doing the swashplate friction check. The hex head is 5/32" drive. An allen wrench is easier to get in to tight areas than a long phillips screwdriver. Can also be used as jackscrews where a 1/4 28 jackscrew is needed.

412 Collective Drill Jig For TB412-00-166

This drill jig is to comply with TB412-00-166. The TB requires you to drill a 1/16" hole sideways into the collective through the aluminum portion of the throttle. The bottom shows a sample piece of aluminum drilled using the jig to check out and show...

S76 Tail Rotor Crosshead Remover

Installs on the crosshead in a matter of seconds by one person instead of several minutes and two people as the factory puller requires.  Removes the crosshead at a fraction of the price of the factory tool.Made from 6061 aluminum so it will not...

S76 Tail Rotor Cable Bullets

These have both left hand and right hand threads to aid in removing and installing the aft tailrotor cables. Screw on the cable ends and thread .020 safety wire through the holes drilled in the end. For AFT cables only.

S76 Tail Rotor Pitch Change Bearing R&R Work Aid

Saves time and slowly presses the bearing in or out. You don't need a hydraulic or arbor press. You don't beat it in/out with a hammer. The risk of damaging a part when using a hammer is so great it's a no-brainer. The cost of one damaged tail rotor or...

S76 Main Rotor Pitch Change Bearing R&R Work Aid

Change bearings on the aircraft in just a few minutes.  Remove the bolt only on the bearing requiring change.  Leave the other end attached. Saves lots of time.

S76 Rotating Scissors Bearing R&R Work Aid

Work aid to press the rotating scissors bearing in and out of the swashplate. Don't waste time chasing sockets that will match up with the OD's and ID's. Not to mention the extensions that get deformed when you beat on them with a hammer while driving...

S76 Main Rotor Damper Bearing R&R Work Aid

Makes R&R of damper bearing a 15 minute job.Change the bearing on the aircraft. No need to remove the damper, bleed, etc

S76 Trim Tab Gauge

S76 Main rotor trim tab gauge. Comes with dial indicator and protective case.

S76 Flight Control Rigging Kit

All the pins, spacers, etc that are needed for rigging the S76 model helicopter.  Parts and pieces are available separately.

Twist Grip Drive Tube and Control Pinion Attachment Work Aid

Twist Grip Drive Tube and Control Pinion Attachment Work AidP/N: ASB76A006Used to check correct bonding strength of the control pinion on the pilot and copilot collective lever driver tubes.

AS350 Swashplate Shimming Aid

For those of you familiar with shimming the AS350 series swashplate you've probably had to rent this before and know what it is. 350A93-3714-00

AS350 Flight Control Rigging Kit

Rent:  $200/Day - Rent starts upon arrival at your location   AirBus no longer offers this kit for rent.

MD500 Tail Rotor Pitch Bearing Installer

Specify which installer you need according to the bearing P/N's shown above.

MD500 SWASHPLATE GREASE PLATE

Designed with 4 grease zerks to make greasing the swashplate quicker and easier than other work aids out there.

MD500 Main Rotor Upper Scissor Crank Bearing R&R

R&R main rotor scissor crank bearing without wasting time trying to find sockets and bolts to press the bearing in and out. ​It has been brought to my attention that after several bearings have been changed that the bore tends to...

MD500 Main Rotor Lower Scissor Crank Bearing R&R

R&R the lower scissor crank bearing. This consists of installer and remover for the lower scissor. Due to the tight outer ear we had to make a fitting to clear the curved edge when installing the bearing.Removal only requires the receiver and bolt.

MD500 Main Rotor P/C Link Trammel

Adjustable trammel for the MD500 p/c links.  This may fit other MD products.One bolt is 5/16" and the opposite end is 1/4".Distance between bolts is about 6 3/8" with plenty of adjustment remaining.

Spindle Boot Plate

MD369/500 Tail Rotor Rigging Gauge

Color varies when manufactured 3D Printed, made from PLA. Gauge for rigging tail rotor on 369/500.

AS350 Flight Control Rigging Kit - DAILY RENTAL

Rent:  $200/Day - Rent starts upon arrival at your location   AirBus no longer offers this kit for rent.

407 Swashplate Shipping Plate

Color varies when manufactured Protects swashplate and uniball from getting bounced around and beat up during shipping.

EC135 Servo Pack Holding Fixture

EC135 servo pack holding fixture

Swashplate Gimbal Ring Bolt Removal Workaid (204B, 205, 212 & 412)

Swashplate Gimbal Ring Bolt Removal Workaid (204B, 205, 212 & 412)   204B-22-27 205-22-45 205B-22-29 212-22-74 412-22-93

206L Cyclic Servo Bellcrank Work Aid

Work Aid acquired through purchase of HeliTools inventory. Something to do with setting of Cyclic Servo Bellcrank on the roof/deck. If you know, let us know exactly how it works so we can update this description.   206-FC-F-04L

206/505 Tail Rotor Rigging Flap Lock Work Aid

Bell designed flap lock for 206/505. These were acquired through purchase of HeliTools inventory. Limited supply.     See our design here.

407 Trim Tab Bender

Used to make adjustments on main rotor trim tabs during tracking.  Comes with protective case.  Bell P/N T103316 & T103317

206 Collective Low Position Rigging Work Aid

Used to set the low collective position (2.40 inches) during rigging as required by the maintenance manual.   206-FC-F-01