Shop by Make & Model

407 Swashplate Overhaul Work Aids - 23pcs set

​Consists of 23 pieces for overhaul of the 407 swashplate as per CR&O

407 Main Rotor Hub Assembly/Dis-assembly Work Aid - 5pcs set

Contact us for individual piece pricingWork aid for assembly and dis-assembly of the mainrotor hub.  Fig 62-4 Items 3, 8, 9, 10

407 Tail Rotor Gearbox Input Wear Sleeve Installer - 2pcs set

Tail rotor gearbox input wear sleeve installer

407 Tail Rotor Gearbox Input Lip Seal Work Aids

Tail Rotor Gearbox Input Lip Seal Remover and Installer Work Aid #1 & #2

Rolls-Royce 250-C20 Starter/Generator & Fuel Pump Seal Installer

This is the new seal installer from Rolls-Royce's Commercial Service Letter. This was designed for installing the new lip seals (23091467) which include a supplied installation mandrel.Although it will also work on the old lip seals (23079054) we,...

Bell 429 & 505 Live Mount Gauge

Pressure gauge in 2 psi increments (as per Bell Maintenance Manual) to calibrate live mounts on 429 and 505.Disclaimer:  The manufacturer of the gauge will not warranty any gauge shipped out of the continental U.S. I can furnish a...

429 Idler Link Bushing R&R

Remove and replace the ilder link bushings as per the maintenance manual.

429 Fan Shaft Assembly Work Aid - 4pcs set

429 Fan shaft assembly work aid per Bell specs.

Bell 505 Tail Boom Rigging Pin - 143

​Required for rigging the tailboom on the 505. 427-201-001-143

Bell 505 Tail Boom Rigging Pin - 147

​Required for rigging the t/boom on the 505. 427-201-001-147

AS350 Swashplate Shimming Aid

For those of you familiar with shimming the AS350 series swashplate you've probably had to rent this before and know what it is. 350A93-3714-00

AS350 Flight Control Rigging Kit

Rent:  $200/Day - Rent starts upon arrival at your location   AirBus no longer offers this kit for rent.

MD500 Tail Rotor Inner Feathering Bearing Removal

Removes the inner feathering bearings as per the component overhaul manualWe also have the installation work aid for the 369A1716-3, -5, -7, -9, -17, and -19 bearings 

MD500 Tail Rotor Pitch Bearing Installer

Specify which installer you need according to the bearing P/N's shown above.

MD500 Main Rotor Upper Scissor Crank Bearing R&R

R&R main rotor scissor crank bearing without wasting time trying to find sockets and bolts to press the bearing in and out. ​It has been brought to my attention that after several bearings have been changed that the bore tends to...

MD500 Main Rotor Lower Scissor Crank Bearing R&R

R&R the lower scissor crank bearing. This consists of installer and remover for the lower scissor. Due to the tight outer ear we had to make a fitting to clear the curved edge when installing the bearing.Removal only requires the receiver and bolt.

Rolls-Royce RR300 Seal Installer

This is the new seal installer from Rolls-Royce's Commercial Service Letter. This was designed for installing the new lip seals (23091467) which include a supplied installation mandrel.

Rolls-Royce 300 Aft PTO Seal Installer

Name describes it all.

Rolls-Royce 300 PTO Seal Remover

Name describes it all.

Spindle Boot Plate

Rolls-Royce 250 Turbine Wheel Lock

Used to lock the turbine wheel in place when installing the turbine section. The plate and rod are made from brass. The brass rod is soft enough to bend if necessary so it won't damage the turbine blades should excessive pressure be applied to the...

Rolls-Royce 250 St. Gobain PTO Seal Installer

These are the seal installers for the new St Gobain seals p/n 23091293 (red) and p/n 23091353 (blue)They can also be used for installing the Viton SealsThe C20 and C30/47 have different seal insertion depths so order according to your engine model

206 Main Rotor Trunnion Centering Fixture

Specify which model aircraft (B or L) when ordering. This is the new and improved main rotor trunnion centering work aid. We have a memo with 5 pages of information on operation of the work aid that we can email to you.   If you are on a budget or...

206A/B/L Mast Assembly Work Aid #3

Work Aid #3 for the Mast Assembly found in the CR&O manual. Chapter 63-10 page 29.

429 Main Rotor Blade Sling

Main rotor blade sling aids in safely removing and installing main rotor blades. The 429 puts you at the upper limits of safely R&R the main rotor blades due to the hight of the blades, your work stands and short mechanics. Even a tall guy has to...

205/212 Blade Bolt Socket

Fits both the 205 and 212 blade bolt nut P/N 204-011-153-001

Blackhawk Door Storage Rack

This rack was made for the local guard unit. It holds up to 8 doors.Specify the number of door slots needed.

RR250-C30/C47 Spur Adapter Gear O'ring Installation Work Aid

For engines C30 and C47 only RR P/N 23006785

EC135 Lifting Clevis

M12669/P-1 1948631 L070P10T1101  

407 Swashplate Shipping Plate

Color varies when manufactured Protects swashplate and uniball from getting bounced around and beat up during shipping.

205/212/412 Transmission Input Quill Pusher Set

Pusher Set - 3pcs To install transmission input quill Bell P/N T101586

407 Hydraulic Pump Spline Wear Pins

407 Hydraulic pump splines wear pins .0200" (x2) & .0400" (x2) Click here for a selection of different size pins

Rolls-Royce 250 Starter/Generator Seal Installer & Fuel Pump Seal Installer - 2pcs

This work aid is a 2 in 1. Use it on either the starter/generator seal or the fuel pump seal. Simplifies installation of seals and removes chances of damaging seal while installing.  This work aid is only for lip seal (23079054).

EC135 Servo Pack Holding Fixture

EC135 servo pack holding fixture

206/407/505 Tail Rotor Gearbox Input/Output Bearing Retaining Nut Wrench

Used to apply torque to the input bearing retaining nut and the output bearing retaining nut. T101512 206-TRGB-F-04  

206/505 Transmission Bearing Installation and Removal Plug

P/N 206XBS-HT   Used to support the input driven spiral bevel gearshaft duplex bearing by the outer race while pressing bearing into or out of the transmission lower case.   T101503   206-XMSN-OH-25

206/505 Transmission Gear Shaft Nut Wrench

Used to apply torque to the input driven spiral bevel gearshaft duplex bearing outer ring retaining nut. Bell P/N T101502 Helitools' P/N 206-XMSN-OH-03

206/505 Mast Holding Fixture

Used to hold the mast assembly when torque is applied to the ball bearing retaining nut during removal and installation. Bell P/N 206-240-002-101 Helitools P/N 206-MAST-F-05   CLICK HERE FOR T101499

407 Mast Bearing Work Aid

P/N 407MBR-HT   Used to remove the bearing from the mast assembly.   T103318-101   407-MAST-OH-03

407 Torque Multiplier Fixture

P/N 407TMF-HT   Used with your choice of a 4-1 or 3-1 torque multiplier.  Let the torque multiplier bump up against the pin to hold backup.This fixture lets you do the mast nut torque or 1-5 hr torque check by yourself not to mention...

206/505 Trunnion Hex Screw Wrench

Used to torque hex insert screw in trunnion/pillow block.   206-MR-OH-18

206 & 505 Main Rotor Blade Alignment Pins - 2pcs

Easier and faster than mirrors and cheaper than a laser.No calibration needed. Drop it in the bolt hole and set the string.   206-MR-F-06

407 Tailrotor Gearbox Quill Wrench

Used to remove, install or torque the nut from the tail rotor gearbox quills.   T101449   407-TRGB-F-05 407-XMSN-F-03

Rolls-Royce 250 PTO Seal Remover

Used to remove single lip PTO seal on RR250 engines.   Thread into the seal and use slide hammer to remove.

206 Planetary Shaft Sleeve

Used to remove aand install the planet gear shaft from and into the arm of the spider and the bearing assembly inner race.   T101506   206-XMSN-OH-20

AS350 Flange Lock Wrench

Has 2 sets of bolt patterns to fit Main Gearbox Input Flange, Brake Disc, Tail Rotor Gearbox Input Flange, and Engine Flanges.    350A93-3205-00

206/407/505 Freewheeling Unit Wrench

Used to remove and install the 214-040-241 nut.    This tool replaces wrench assembly 407-240-006-101.   206-FWU-OH-18   T101960

206/505/407 Freewheeling Unit Duplex Bearing Removal Driver

Used to remove the 406-040-531 bearing from the 406-040-508 Cap Assembly.   206-FWU-OH-15   T103324-101

206/407/505 Freewheeling Unit Bearing Installation Sleeve

Used to install the 206-040-206 bearing into the 406-040-516 shaft.    206-FWU-OH-17   T103333

222 Tail Rotor Gearbox Holder

Fixture to hold Tail Rotor Gearbox.   222-TRGB-OH-01 222-TRGB-OH-1B   T103036

206/407/505 Freewheeling Unit Shaft Removal Work Aids

Used in conjuction with a press to remove the shaft from the bearing.   T103310-101

429 PW207 Mag Seal Puller

Slide Hammer used to remove Seal P/N 3058291-01   PWC64888 PWC64888-1    Designed with customer to fit tighter than PWC factory workaid. All 3 lips engage. 

C30/47 #1 Bearing in Compressor Puller

C30/47 #1 Bearing in Compressor Puller   23005023

Oil Collector Pan - Alignment Pilot Workaid

Oil Collector Pan - Alignment Pilot Workaid for top case 206-040-550   Figure 63-19

Oil Collector Pan - Alignment Pilot Work aid

Oil Collector Pan - Alignment Pilot Work aid for top case 206-040-532   Figure 63-19

Oil Collector Pan - Alignment Pilot Work Aid Set

Oil Collector Pan - Alignment Pilot Work Aid Set   For top case 206-040-550 & 206-040-532    Figure 63-19

206/407/505 Tail Rotor Output Shaft Nut Work Aid

Used to apply torque to and remove the output shaft inner nut.   T101513   206-TRGB-OH-05

206/505 Tail Rotor Gearbox Backlash Work Aid

Used to hold output shaft so you can check the backlash between the tail rotor gearbox input pinion gear and output bevel gear.   T102093   206-TRGB-OH-06

407 Mast Assembly Nut Wrench

Wrench is used to remove and torque the nut on the mast assembly bearing during overhaul.   407-240-007-101/105 407-240-007-105   407-MAST-02

205/212/214/412 External Spline Wrench

205/212/214/412 External Spline Wrench   412-XMSN-OH-01   T101306

206 Tail Rotor Bearing Installation

Used in conjuction with a hydralic press to push out the bearing from the side of the blade that has the swaged lip.

407 Freewheeling Unit Nut Wrench

Used to install the freewheel nut   407-FWU-OH-21   407-240-006

407 Transmission Input Pinion Assembly And Removal Adapter

Used in conjunction with a puller to remove and install the transmission pinion assembly   Helitools 407-XMSN-OH-02   Bell 407-240-003

206B/L/505 Main Rotor Static Balance Kit

Static Balancing Kit for 206B/L and 505. Comes in protective case with extra plastic bin to store lead weights. This is from Chuck Dugan from Helitools. We acquired his inventory. Contact us for any other tools that was previously supplied by...