AS350 Tail Rotor Hub Spherical Laminated Bearing Replacement Work Aid MSRP: Was: Now: $450.00 Add to Cart
EC135 Tail Rotor Inspection EASB EC135-64-11-0001 Work Aid MSRP: Was: Now: $190.00 - $620.00 Choose Options
S70/UH-60 Tail Rotor Bolt Star Plate Helps you organize your bolts Material: Aluminum Size: 12" x 12" x 1/2" Country Of Origin: USA Manufacturer: Helicopter Work Aids Airframes: S70, UH-60A,L,M, & G Component/Assembly: Tail Rotor ATA Chapter: 64 Weight: 3lbs MSRP: Was: Now: $350.00 Add to Cart
S70/UH-60 Tail Rotor Pitch Beam Remover Required fixture to facilitate safe removal of pitch beam. 5120-00-948-3923 PBP-60-AA Material: Aluminum & Steel Size: 15" x 3.5" x 6.75" Country Of Origin: USA Manufacturer: Helicopter Work Aids Airframes: S70, UH-60A,L,M, &... MSRP: Was: Now: $4,900.00 Add to Cart
MD500 Tail Rotor Swashplate Lock Nut Torque Wrench Adapter Wrench to remove and torque lock nut in the pitch control assembly. Ours, as you can see in the pictures, have smaller tapered teeth so that it only engages the lock nut. The tool will not interfere with the tang washer. Much easier to use than other... MSRP: Was: Now: $425.00 Choose Options
S70/UH-60 Tail Rotor Pitch Beam Spanner Wrench Pin spanner wrench to remove the mast nut from the tail rotor. Material: Aluminum Size: 3" x 3" x 1/2" Country Of Origin: USA Manufacturer: Helicopter Work Aids Airframes: S70, UH-60A,L,M, & G Component/Assembly: Tail Rotor ATA Chapter:... MSRP: Was: Now: $150.00 Add to Cart
AS350 Tail Rotor Hub Spherical Laminated Bearing Replacement Work Aid Tool used to remove the laminated spherical bearing. Does not come with the holder. 350A93331203 MSRP: Was: Now: $450.00 Add to Cart
429 Tail Rotor Balance Work Aid Work aid for balancing the tail rotor on the 429 If after three adjustments it is not possible to achieve successful dynamic balance of the tail rotor assembly, this workaid 111486325 can be installed to help the tail rotor balance process and to... MSRP: Was: Now: $250.00 Add to Cart
206/505 Tail Rotor Static Balance Kit Static balancing kit for the Bell 206 and 505. This balancing kit is similar to our main rotor kit in that it is hung and not on a table top. MSRP: Was: Now: $2,500.00 Add to Cart
10X Magnifying Glass We chose this model of magnifying glass because the cup is setup for the correct focal distance. Just place the magnifying glass on the object you are trying to inspect and you are focused. No fighting the loupe trying to figure out the correct focus... MSRP: Was: Now: $20.00 Add to Cart
407 Tail Rotor Hub Flapping Bearing Work Aid Used to apply the force for installation and removal on steel outer race of flapping bearing. That wording is straight from the manual. Bell P/N T101750 MSRP: Was: Now: $775.00 Add to Cart
EC135 Tail Rotor Inspection EASB EC135-64-11-0001 Work Aid One of the tools required for performing inspection per EC135 EASB EC135-64-11-0001 EASA AD 2024–0028–E FAA AD 2024–04–10 MSRP: Was: Now: $190.00 - $620.00 Choose Options
S70/UH-60 Tail Rotor Blade Boot Installation Work Aid This tool is used to stretch the blade boot for ease of installation on the tail rotor hub. Don't know why I explained this, you already know what its for if you are looking for it. MSRP: Was: Now: $85.00 Add to Cart
MD500 Tail Rotor Drive Fork Bushing This tool removes that Tail Rotor Drive Fork Bushing P/N 369A1604 in the strap pack. RBA1600-80902 269T9319 369A1600-80902 MSRP: Was: Now: $175.00 Add to Cart
212/412 Tail Rotor Trunnion Centering Tool Figure 64-14 Tail Rotor Trunnion Centering Tool MSRP: Was: Now: $550.00 Add to Cart
206L Tail Rotor Rigging Go/No-Go Gauge Use this Go/No-Go Gauge to set the 1.46" on the bellcrank at the bottom of the vertical tunnel (broom closet) during tail rotor rigging. Helitools 206-FC-F-07 MSRP: Was: Now: $45.00 Add to Cart
206 Tail Rotor Rigging Work Aid Color varies when manufactured Made from PLA. Light and soft to protect tail rotor blades.Much lighter than the factory tool made from steel. Cheap enough you can purchase 2 pieces like Bell suggests in the maintenance manual to speed up the job. This... MSRP: Was: Now: $245.00 Choose Options
206B&L Tail Rotor Gearbox Drain Tail Rotor Gearbox Drain for the 206 series aircraft. Comes with 7 ft hose. DB3225L MSRP: Was: Now: $95.00 Add to Cart
206 Tail Rotor Mast Nut Socket 206 series tail rotor retaining nut extended socket. MSRP: Was: Now: $95.00 Add to Cart
206 Series Tail Rotor Crosshead Remover Used to remove the tailrotor crosshead on Bell 206 series aircraft.Safer and faster than the 2 jaw pullers. MSRP: Was: Now: $295.00 Add to Cart
206 Tail Rotor Balance Wheel Adapter No longer will you have to use a flathead screwdriver and mallet to unscrew the balance wheel. Can also be used for torquing when the 1/4" drive cutouts on the balance wheels are worn and won't hold the torque wrench. MSRP: Was: Now: $40.00 Add to Cart
206 Knurl Nut Wrench This will easily remove that stuck knurl nut. It is especially great if you want to replace the knurl nut liner and don't want to ruin the knurl nut with channel locks because the knurl nut is frozen. MSRP: Was: Now: $130.00 Add to Cart
206 Tail Rotor Flap Stop Work Aid This item is 3D printed, made out of PLA. Color may vary. This work aid was designed to replace the Bell designed fork shaped lockout work aid. The 206 tail rotors are shimmed between the tailrotor hub and flap stop. That means every tailrotor is... MSRP: Was: Now: $195.00 Choose Options
206 Tail Rotor Trunnion Grease Housing Bearing & Seal Installer Double sided work aid to press the bearing and seal into the needle grease fitting housing assembly on tail rotor hub. MSRP: Was: Now: $210.00 Add to Cart
206 Tail Rotor Trunnion Inner Race Installer & Plugs Work aids to press the inner race onto the tail rotor trunnion. This is also the Bell 505 Tail Rotor Work Aid #7 & #8 MSRP: Was: Now: $245.00 Add to Cart
206 Tail Rotor Hub Trunnion Fixture Fills in the trunnion, so it is not crushed during pressing of wear sleeves. MSRP: Was: Now: $50.00 Add to Cart
407 Tail Rotor Mast Nut Wrench Use this wrench to torque and perform torque checks of the 407 tailrotor mast nut. Pull quick release pin and slide wrench onto mast nut. Use 3/8 drive torque wrench. This wrench fits better than the large bulky crowsfoot. Send us a scrap tail... MSRP: Was: Now: $275.00 Add to Cart
407 Tail Rotor Rigging Block Color varies when manufactured Used with the 407 tail rotor flap stop work aid to check or rig the tail rotor system. Ours (Helicopter Work Aids) is 3D Printed, made with PLA. Very tough but not as heavy as the steel blocks that Bell... MSRP: Was: Now: $245.00 Choose Options
407 Tail Rotor Flap Lock Work Aid For Rigging This work aid is used to stop the tail rotor from flapping when checking the blade pitch angles. This is used in conjunction with the 407 tailrotor rigging block which is used to check the pitch angle. Bell P/N 407-99-26-101 found in ASB... MSRP: Was: Now: $425.00 Add to Cart
407 Tail Rotor Flap Stop This work aid is used to stop the tail rotor from flapping when checking the blade pitch angles. This is used in conjunction with the 407 tailrotor rigging block which is used to check the pitch angle. This is our lightweight 3D printed... MSRP: Was: Now: $285.00 Add to Cart
429 Tail Rotor Gearbox Drain Tailrotor gearbox drain comes with a 7 ft hose. Probably don't need a 7 ft hose on a tailrotor gearbox drain, but that's what you get. You can shorten it to any length you want. MSRP: Was: Now: $95.00 Add to Cart
429 Tail Rotor Mast Nut Socket Socket made as per Bell specifications. Requires removal of crosshead to perform torquing procedure. Drive is 3/4" MSRP: Was: Now: $115.00 Add to Cart
429 Tail Rotor Mast Nut Wrench Remove one of the allen screws and spread open the work aid. Close it back together and reinstall the screw. Torque the nut and then remove the screw and work aid. Almost as fast as reading this description. Does not require removal of crosshead. MSRP: Was: Now: $325.00 Add to Cart
S76 Tail Rotor Crosshead Remover Installs on the crosshead in a matter of seconds by one person instead of several minutes and two people as the factory puller requires. Removes the crosshead at a fraction of the price of the factory tool.Made from 6061 aluminum so it will not... MSRP: Was: Now: $910.00 Add to Cart
S76 Tail Rotor Cable Bullets These have both left hand and right hand threads to aid in removing and installing the aft tailrotor cables. Screw on the cable ends and thread .020 safety wire through the holes drilled in the end. For AFT cables only. MSRP: Was: Now: $65.00 Add to Cart
S76 Tail Rotor Pitch Change Bearing R&R Work Aid Saves time and slowly presses the bearing in or out. You don't need a hydraulic or arbor press. You don't beat it in/out with a hammer. The risk of damaging a part when using a hammer is so great it's a no-brainer. The cost of one damaged tail rotor or... MSRP: Was: Now: $165.00 Add to Cart
MD500 Tail Rotor Inner Feathering Bearing Removal Removes the inner feathering bearings as per the component overhaul manualWe also have the installation work aid for the 369A1716-3, -5, -7, -9, -17, and -19 bearings MSRP: Was: Now: $525.00 Add to Cart
MD500 Tail Rotor Pitch Bearing Installer Specify which installer you need according to the bearing P/N's shown above. MSRP: Was: Now: $125.00 Choose Options
MD369/500 Tail Rotor Rigging Gauge Color varies when manufactured 3D Printed, made from PLA. Gauge for rigging tail rotor on 369/500. MSRP: Was: Now: $45.00 Add to Cart
MD Tail Rotor Nut Wrench Tail Rotor Nut Wrench (MD29823-5A) for: MD500 MD500D MD500E MD520N MD530F MSRP: Was: Now: $125.00 Add to Cart
206/505 Tail Rotor Rigging Flap Lock Work Aid Bell designed flap lock for 206/505. These were acquired through purchase of HeliTools inventory. Limited supply. See our design here. MSRP: Was: Now: $25.00 Add to Cart
206 Tail Rotor Bearing Installation Used in conjuction with a hydralic press to push out the bearing from the side of the blade that has the swaged lip. MSRP: Was: Now: $375.00 Add to Cart