BELL-206

206L Transmission Drain

Main transmission drain for the 206L series aircraft. Bell P/N: DB3188L

Slide Hammer

Shorter than commercial slides to pop out fuel pump cartridges in the belly when there is little ground clearance available.Comes with 7/16 20 and a 1/4 28 thread adapters.

206 Tail Rotor Mast Nut Socket

206 series tail rotor retaining nut extended socket.

206 Series Tail Rotor Crosshead Remover

Used to remove the tailrotor crosshead on Bell 206 series aircraft.Safer and faster than the 2 jaw pullers.

Bypass Spool Check Mount - With Dial Indicator

Bracket held on with nylon screws so as not to damage the servo anodized surface.The bracket also comes with a powder coat finish which gives additional protection to the anodized finish on the servo...

Rolls-Royce 250 Ignitor Wrench

Ignitors can be hard to remove for several reasons. Someone put it in too tight, didn't use anti-seize or used a 12 point socket and slipped, rounding off the corners. This wrench is made from a 6...

Rolls-Royce 250 Starter/Generator Spline Turn Wrench

T-handle wrench for turning the N1 wheels while doing maintenance on the RR250 series engines. Starter/generator splines are hard to find, so get yours here   Rolls-Royce P/N 6799790

206 & 407 Free Wheeling Unit Aft Flange Wrench

Use this work aid by attaching it to the aft flange with two bolts. Use a breaker bar to keep shaft from rotating. Through the larger centered hole, use your socket to torque the nut. We can make the...

Reversible Swing Wrenches

These reversible swing wrenches are an improvement over our other wrenches. We are using the reversible Gear wrench brand so when you get into a tight spot and can't get the wrench off the nut or...

Brass Screwdriver For Compass Adjustment

No more trying to make a screw driver for adjusting compasses with a hammer and welding rod.This is a quality, solid brass screwdriver made especially for adjusting compasses.It's 4 3/4 inches long...

206/505 Transmission Input Flange Wrench

T101555 transmission input flange wrench for the 206.

206/407/505 Oil Cooler Blower Driveshaft Spanner Wrench

Wrench to get off the spanner nut on the oil cooler blower. The L-model wrench will also work on the 407.

206 Oil Cooler Blower Driveshaft Spanner Socket

A better fitting work aid to remove the oil cooler blower driveshaft spanner nut.

206 Air Conditioner Pulley Wrench

This air conditioner pulley wrench avoids elongating the pin hole when using a pin spanner, plus it stays in place when torquing.

206 Tail Rotor Balance Wheel Adapter

No longer will you have to use a flathead screwdriver and mallet to unscrew the balance wheel.   Can also be used for torquing when the 1/4" drive cutouts on the balance wheels are worn and won't...

206 Knurl Nut Wrench

This will easily remove that stuck knurl nut. It is especially great if you want to replace the knurl nut liner and don't want to ruin the knurl nut with channel locks because the knurl nut is frozen.

206 Tail Rotor Flap Stop Work Aid

This item is 3D printed, made out of PLA. Color may vary. This work aid was designed to replace the Bell designed fork shaped lockout work aid. The 206 tail rotors are shimmed between the tailrotor...

206/505 Tail Rotor Gearbox Spanner Nut Wrench

Used to remove or install the locknut on the input side of the tailrotor gearbox. Easier to use than the AN8514-1 spanner wrench.   Helitools P

Bell Rotor Brake Bleeder Kit

Oil can comes with 6 feet of hose and allows bleeding the brakes to be a one man job. Fits most Bell models. Quickest way to bleed rotor brakes. Avoid making a mess with our rotor brake bleeder...

KaFlex Tourniquet Compression Kit for 206L and 407

This is the easiest and fastest way to R&R 206L and 407 KaFlex shafts.Simply make 2 wraps on the driveshaft passing through the holes in the aluminum rods, tie a knot and twist the rods until the...

Swing Wrenches

Don't buy bulky swing wrenches from tool trucks made from the old ratcheting dog bone wrenches that were great 40 years ago. Ours are made with the slimmer profile Gearwrench ratcheting boxends...

Bell 206/505 Mast Nut Socket

This 7/8 - 3/4 drive socket has been bored out to fit properly on the mast nut. PD2734

Rolls-Royce 250 Idle Adjustment Swing Wrench

This swing wrench is made specifically for adjusting the idle on the 206 RR250 engine. Of course with that in mind, you can also use it for any tight spot that requires a 1/4" box end wrench. We have...

Rolls-Royce 250 Exhaust Stack Wrench

Wrench is made for removal of the nuts on the exhaust stack. Keeps nuts from falling into crevices of the engine.

Bell Sight Glass Remover

Work aid to remove the round Bell sight glass.

Composite Tap Hammer

Use the tap hammer on main rotor blades or any other composite material to check for delamination.   Equivalent to T75449-2       Aluminum: Softer impact. Good for thin laminates or delicate surfaces...

Grease Fittings

These are the threaded ones, not the quick disconnect ones that get grease everywhere except the part you want it in.

90° Grease Coupler

I recently found this 90 degree grease coupler that works great on hard to access grease fittings.Works really well on the oil cooler blower bearings on the Bell 407. It slides in from the side when...

Jackscrews 1/4" 28 - 3pcs

Use these on transmission input quills, freewheeling unit, tailrotor gearbox, or any component requiring 1/4" 28 jackscrews. T101308

206 Main Rotor Grip Excluder Seal Remover

Insert into the excluder bushing, turn knob to tighten which expands fingers on the end and remove seal.

206 Tail Rotor Trunnion Grease Housing Bearing & Seal Installer

Double sided work aid to press the bearing and seal into the needle grease fitting housing assembly on tail rotor hub.

206 Tail Rotor Trunnion Inner Race Installer & Plugs

Work aids to press the inner race onto the tail rotor trunnion.   This is also the Bell 505 Tail Rotor Work Aid #7 & #8

206 Main Rotor Grip Excluder Mandrel

If you need this, you know what it is for.

Rolls-Royce 250 C30/C47 Gearbox PTO Seal Installer

This installer works on the C30 and C47 engines.  You can install one seal at a time or both at once. This is the best seal installer you will find for the gearbox seals.   406-240-001-101

Rolls-Royce 250 C30/C47 Gearbox PTO Seal Remover

Removes rear gearbox seal. 406-240-009-115

206/505 Latch Bolt Nut Socket

This socket is normally used in the shop for removal of the latch bolt on the grip assembly. See item #4 in one of the posted pictures. Bell P/N T101554

206 Main Rotor Blade Friction Pad Bonding Clamp

Main rotor blade friction pad bonding clamp. Can do both the grip and the blade's friction pad

Rolls-Royce 250 C30/C47 Bleed Valve Shop Air Adapter

Rolls-Royce 250 Quick Disconnect Coupling For Engine Rinse

Name says it all.

206A/B Freewheeling Assembly Work Aid #4

Work Aid #4 for the Freewheeling Assembly found in the CR&O manual.   Chapter 63-30 page 264.

206A/B Freewheeling Assembly Work Aid #5

Work aid #5 for the Freewheeling Assembly found in the CR&O manual. Chapter 63-30-00 page 141.

Saft Battery Cap Pressure Tester

This manifold is for pressure testing the saft battery caps. We will need you to send us the caps you want the manifold manufactured for. Pictured are two different battery caps. If the battery cap...

206L Transmission Tach Generator Driveshaft Work Aid

Work aid to remove and replace tach generator driveshaft as seen in figure 63-7c

206 Main Rotor Hub Pitch Horn Lock

Use this work aid when lifting the hub assembly from the mast. Remove upperside of pitch control links and install the work aid.

206 Tail Rotor Gearbox Vise Mount

Mount tail rotor gearbox to shop vise for assembly, disassembly, repairs and backlash check.

Bell 206 Tail Boom/Fuselage Former Ring Fixture

Used for replacing tailboom/fuselage former ring or tail boom attach fittings on the 206B and L series. Fixture includes a removable drill bushing for drilling the 3/16" pilot hole.

206 Tail Rotor Hub Trunnion Fixture

Fills in the trunnion, so it is not crushed during pressing of wear sleeves.

206 Swashplate Uniball Fixture

Supports lower portion of uniball when pressing in the lower bushings.

206 Swashplate Uniball Lower Bushing Remover

Removes lower bushings from swashplate uniball.

Rolls-Royce 250 Power Turbine Support Cleaning Kit

Kit comes in a foam insert for easy storage and handling.   RR P/N 23007615 RR P/N 23003267

Torque Adapters 1/4" Drive

Hard to find 1/4" drive torque adapters. Most torque adapters you will find are 3/8" drive. These will allow you to use that low torque 1/4" torque wrench without the 3/8" to 1/4" adapter.   SAE: The...

206 & 407 Transmission Oil Pump Puller

Slide hammer for transmission oil pump on 206s and 407s.

206/407 Transmission Oil Pump & Housing Assembly Work Aid

If you're looking for this, you already know what it's for. TB206L-05-218 TB407-05-65

206/407 Hydraulic Pump Shaft Remover

Work aid that helps easily remove the hydraulic pump shaft. You will no longer need to pry out the shaft with pliers and have the shaft and spring flying across the hangar, or worse, a grassy field...

407 Tail Rotor Gearbox Output Seal Work Aid

Install or remove the tail rotor gearbox output seal.

RR250 C30/C47 Compressor/Diffuser Orifice R&R Work Aid

Use this work aid to remove and re-install the orifice when it is located in the exhaust collector.Good on any 206L with C30 installed, 407, and Sikorsky S-76A.

Rolls-Royce 250-C20 Starter/Generator & Fuel Pump Seal Installer

This is the new seal installer from Rolls-Royce's Commercial Service Letter. This was designed for installing the new lip seals (23091467) which include a supplied installation mandrel.Although it...

Air Conditioner Belt Tensiometer

Belt Tensiometer specified by Bell for checking air conditioning belt tension.   Scale reads in pounds and kilograms Measures tension from 30 to 160 lb., and 15 to 75 kg. Die-cast aluminum body,...

Rolls-Royce 250 Oil Pressure Regulator Socket

1/4 inch drive socket for adjusting the oil pressure regulator.Makes it easy to adjust and count the turns plus it won't eat up the regulator adjusting bar when using needle nose pliers like other...

Rolls-Royce 250 Turbine Wheel Lock

Used to lock the turbine wheel in place when installing the turbine section. The plate and rod are made from brass. The brass rod is soft enough to bend if necessary so it won't damage the turbine...

Rolls-Royce 250 St. Gobain PTO Seal Installer

These are the seal installers for the new St Gobain seals p/n 23091293 (red) and p/n 23091353 (blue)They can also be used for installing the Viton SealsThe C20 and C30/47 have different seal...

206L4 Kaflex Mounting Wrench

206L4 Kaflex Mounting WrenchIf you have ever installed a Kaflex drive shaft, you know how its practically impossible to actually torque them. We designed these wrenches so you could stop using that...

206A/B & TH-67 Bonded Coupling Tail Rotor Drive Shaft Wrench - 2pc Set

Used to proof load test installed bonded tail rotor driveshafts to verify the integrity of the bond line. Two required as per ASB 206-20-139 issued 21 July 2020 Also used to comply with AD...

206 Main Rotor Trunnion Centering Fixture

Specify which model aircraft (B or L) when ordering. Fixture comes with one (1) mandrel of your choice. If you need another mandrel for the other 206 model, you can choose that as a separate item...

206L/407/427/429 CORDLESS Portable Hydraulic Pump Drive Unit

Remove the hydraulic pump from the transmission with the hoses still connected and bolt hydraulic pump to the red pump pressure supply. The Cordless Makita is driven by a soft start, 5 speed,...

206A/B/L Mast Assembly Work Aid #3

Work Aid #3 for the Mast Assembly found in the CR&O manual. Chapter 63-10 page 29.

RR250-C30/C47 Spur Adapter Gear O'ring Installation Work Aid

For engines C30 and C47 only RR P/N 23006785

Oil Can Opener

One Black Plastic "Church Key" FOD Free Turbine Oil Can Opener     A certified, FOD-free way to open turbine oil cans. Built for aircraft mechanics who cannot riskdebris in the oil. Opening a can of...

Rolls-Royce 250 Starter/Generator Seal Installer & Fuel Pump Seal Installer - 2pcs

This work aid is a 2 in 1. Use it on either the starter/generator seal or the fuel pump seal. Simplifies installation of seals and removes chances of damaging seal while installing.  This work aid is...

ENGWASH-HF-BRACKET

This is just the brackets and fasterners necessary to attach your (ENGWASHx2) double engine wash bottle set up to a Harbor Fright Welding Cart.  Purchase your own Welding Cart from Harbor Freight and...

206/407/505 Tail Rotor Gearbox Input/Output Bearing Retaining Nut Wrench

Used to apply torque to the input bearing retaining nut and the output bearing retaining nut. T101512 206-TRGB-F-04  

206/505 Transmission Bearing Installation and Removal Plug

P/N 206XBS-HT   Used to support the input driven spiral bevel gearshaft duplex bearing by the outer race while pressing bearing into or out of the transmission lower case.   T101503   206-XMSN-OH-25

206/505 Transmission Gear Shaft Nut Wrench

Used to apply torque to the input driven spiral bevel gearshaft duplex bearing outer ring retaining nut. Bell P/N T101502 Helitools' P/N 206-XMSN-OH-03

206/505 Mast Holding Fixture

Used to hold the mast assembly when torque is applied to the ball bearing retaining nut during removal and installation. Bell P/N 206-240-002-101 Helitools P/N 206-MAST-F-05   CLICK HERE FOR T101499

206/505 Trunnion Hex Screw Wrench

Used to torque hex insert screw in trunnion/pillow block.   206-MR-OH-18

206 & 505 Main Rotor Blade Alignment Pins - 2pcs

Easier and faster than mirrors and cheaper than a laser.No calibration needed. Drop it in the bolt hole and set the string.   206-MR-F-06

206 Planetary Shaft Sleeve

Used to remove aand install the planet gear shaft from and into the arm of the spider and the bearing assembly inner race.   T101506   206-XMSN-OH-20

206L Cyclic Servo Bellcrank Work Aid

Work Aid acquired through purchase of HeliTools inventory. Something to do with setting of Cyclic Servo Bellcrank on the roof/deck. If you know, let us know exactly how it works so we can update this...

206/505 Tail Rotor Rigging Flap Lock Work Aid

This is the Helitools' version of the Bell designed flap lock for 206/505. T101741 See our design here.

206/407/505 Freewheeling Unit Wrench

Used to remove and install the 214-040-241 nut.    This tool replaces wrench assembly 407-240-006-101.   206-FWU-OH-18   T101960

206/505/407 Freewheeling Unit Duplex Bearing Removal Driver

Used to remove the 406-040-531 bearing from the 406-040-508 Cap Assembly.   206-FWU-OH-15   T103324-101

206/407/505 Freewheeling Unit Bearing Installation Sleeve

Used to install the 206-040-206 bearing into the 406-040-516 shaft.    206-FWU-OH-17   T103333

206/407/505 Freewheeling Unit Shaft Removal Work Aids

Used in conjuction with a press to remove the shaft from the bearing.   T103310-101

C20/C30/C47 #1 Bearing in Compressor Puller

C20/C30/C47 #1 Bearing in Compressor Puller   23005023

Oil Collector Pan - Alignment Pilot Workaid

Oil Collector Pan - Alignment Pilot Workaid for top case 206-040-550   Figure 63-19

Oil Collector Pan - Alignment Pilot Work aid

Oil Collector Pan - Alignment Pilot Work aid for top case 206-040-532   Figure 63-19

Oil Collector Pan - Alignment Pilot Work Aid Set

Oil Collector Pan - Alignment Pilot Work Aid Set   For top case 206-040-550 & 206-040-532    Figure 63-19

206/407/505 Tail Rotor Output Shaft Nut Work Aid

Used to apply torque to and remove the output shaft inner nut.   T101513   206-TRGB-OH-05

206/505 Tail Rotor Gearbox Backlash Work Aid

Used to hold output shaft so you can check the backlash between the tail rotor gearbox input pinion gear and output bevel gear.   T102093   206-TRGB-OH-06

206 Collective Low Position Rigging Work Aid

Used to set the low collective position (2.40 inches) during rigging as required by the maintenance manual.   206-FC-F-01

206 Tail Rotor Bearing Installation

Used in conjuction with a hydralic press to push out the bearing from the side of the blade that has the swaged lip.

206B/L/505 Main Rotor Static Balance Kit

Static Balancing Kit for 206B/L and 505. Comes in protective case with extra plastic bin to store lead weights. This is from Chuck Dugan from Helitools. We acquired his inventory. Contact us for any...