Rolls-Royce 250/300 St. Gobain Seal Remover Slide hammer to remove the St Gobain seal on both the RR250 and RR300. MSRP: Was: Now: $900.00 Add to Cart
Engine Wash Bottle SINGLE BOTTLE: This is a stainless, 2 1/2 gallon bottle that has been used by all the major operators in the Gulf of Mexico for the last 45 years to my knowledge. I have replaced the short stock hose with 7 ft of high quality chemical resistant... MSRP: Was: Now: $325.00 - $815.00 Choose Options
407 Kaflex Mounting Wrench If you have ever installed a Kaflex drive shaft, you know how its practically impossible to actually torque them. We designed these wrenches so you could stop using that calibrated elbow and properly torque them with a torque wrench. MSRP: Was: Now: $85.00 Add to Cart
Rolls-Royce 250 C47 Ratcheting Open-End Fuel-Control Swing Wrench Ratcheting open end swing wrench designed to remove that pesky upper 5/16 nut on the fuel control. With a slow and steady control of the swing wrench, I was able to remove the upper nut in approximately three minutes. Compare that to the last time you... MSRP: Was: Now: $85.00 Add to Cart
Rolls-Royce 250 Turbine To Gearbox Attach Bolt Wrenches - 3pcs No longer will you need to use that calibrated elbow. We have designed 3 wrenches to perform the torque checks on the 6 turbine to gearbox attach bolts on the RR250-C30 and C47 engines. A long 1/4" extension will be required to torque the bolt above the... MSRP: Was: Now: $120.00 Add to Cart
Rolls-Royce 250 C30/C47 Fuel Nozzle Wrench This fuel nozzle wrench is double sided to give you better access to the fuel nozzle. With the cowling installed, if you place the wrench on the fuel nozzle, it may not sit the way you want because of the limited space, flip it to the other side. The... MSRP: Was: Now: $125.00 Add to Cart
Rolls-Royce 250 C30/C47 Medium Fuel Nozzle Wrench This wrench is usually preferred by the overhaul guys working the engine on a stand. MSRP: Was: Now: $95.00 Add to Cart
206B Bleed Valve Block Color varies when manufactured Bleed valve block for Rolls-Royce C20 engine with strap so that it can be hung. Rolls-Royce P/N 6886204 MSRP: Was: Now: $38.00 Add to Cart
Rolls-Royce 250 Ignitor Wrench Ignitors can be hard to remove for several reasons. Someone put it in too tight, didn't use anti-seize or used a 12 point socket and slipped, rounding off the corners. This wrench is made from a 6 point impact socket. Install the wrench and put the... MSRP: Was: Now: $65.00 Add to Cart
Rolls-Royce 250 Idle Adjustment Swing Wrench This swing wrench is made specifically for adjusting the idle on the 206 RR250 engine. Of course with that in mind, you can also use it for any tight spot that requires a 1/4" box end wrench. We have 2 types of swing wrenches. Our version and Helitools'... MSRP: Was: Now: $85.00 Choose Options
Rolls-Royce 250 Exhaust Stack Wrench Wrench is made for removal of the nuts on the exhaust stack. Keeps nuts from falling into crevices of the engine. MSRP: Was: Now: $30.00 Add to Cart
Rolls-Royce 250 C30/C47 Bleed Valve Shop Air Adapter Quick disconnect so that you can use shop air to close the Bleed valve. MSRP: Was: Now: $40.00 Add to Cart
Torque Adapters 1/4" Drive Hard to find 1/4" drive torque adapters. Most torque adapters you will find are 3/8" drive. These will allow you to use that low torque 1/4" torque wrench without the 3/8" to 1/4" adapter. SAE: The standard set consists of 1/4", 5/16", 3/8", &... MSRP: Was: Now: $50.00 - $170.00 Choose Options
RR250 C30/C47 Compressor/Diffuser Orifice R&R Work Aid Use this work aid to remove and re-install the orifice when it is located in the exhaust collector.Good on any 206L with C30 installed, 407, and Sikorsky S-76A. MSRP: Was: Now: $85.00 Add to Cart
Pratt & Whitney PW200 Engine Sling Good on the PW200 series engines. MSRP: Was: Now: $275.00 Add to Cart
S76A Main Driveshaft Wrench 2pcs set Consists of 2 wrenches, one for the front coupling and another for the aft coupling. Does not include ratchet, extension or socket. Makes driveshaft R&R quick and easy and avoids spilling blood all over the transmission deck.On the A... MSRP: Was: Now: $210.00 Add to Cart
S76 PTO Shaft Wrench When removing or installing the PTO shaft on the C30 engine you need this fixture to hold a backup on the shaft and also to apply the correct torque so the PTO gear is not over torqued and cracked. MSRP: Was: Now: $110.00 Add to Cart
Turbomeca Engine Oil Filter Wrench Turbomeca engine oil filter wrench to remove the housing cap on the S1 or S2 engine. MSRP: Was: Now: $325.00 Add to Cart
Rolls-Royce 250 Banjo Oil Fitting Wrench Allows you to tighten the banjo fitting with a ratchet or torque wrench. Makes removal a piece of cake too. S76A only. MSRP: Was: Now: $70.00 Add to Cart
Rolls-Royce 250 Oil Pressure Regulator Socket 1/4 inch drive socket for adjusting the oil pressure regulator.Makes it easy to adjust and count the turns plus it won't eat up the regulator adjusting bar when using needle nose pliers like other people used to do. MSRP: Was: Now: $45.00 Add to Cart
Honeywell HTS900 NP Sensor Shimming Work Aid Used for shimming the NP Sensor. Screw the large piece, adapter or bushing or whatever you want to call it into the gearbox. Screw in the center bolt until it contacts the gear tooth.Lock it down using the knurled nut... MSRP: Was: Now: $245.00 Add to Cart
407 HTS900 Engine Oil Filter Socket & Wrench This socket removes the oil filter housing on the HTS900 engine.Socket is removed with a 3/4" flex ratcheting box end wrench. We have the wrench if you don't have the flex style which makes it much easier to get on the attached nut. MSRP: Was: Now: $35.00 - $95.00 Choose Options
