1/4" Drive - 12 point Universal/Swivel Sockets SAE & METRIC MSRP: Was: Now: $60.00 - $85.00 Choose Options
206/407/505 Swashplate Roll Stake Bearing Work Aid Kit MSRP: Was: Now: $250.00 - $3,000.00 Choose Options
Swashplate Gimbal Ring Bolt Removal Workaid (204B, 205, 212 & 412) MSRP: Was: Now: $300.00 Add to Cart
UV Flashlight for Transmission and Engine Oil Leak Checks UV flashlight for detecting oil leaks. Works great in the daytime (with cowlings on), works even better at night. Make sure you wash off your aircraft well before performing a ground run leak check with this light. It will light up ALL your residual oil... MSRP: Was: Now: $30.00 Add to Cart
1/4" Drive - 12 point Universal/Swivel Sockets SAE & METRIC We have located some quality swivel sockets at an affordable price that we are happy to offer here! They are made by Genius Tools. SAE (6pc) set consists of 1/4", 5/16", 3/8", 7/16", 1/2", & 9/16" Metric (9pc) set consists of 6mm, 7mm, 8mm, 9mm,... MSRP: Was: Now: $60.00 - $85.00 Choose Options
206 Main Rotor Grip Seal Holder For Purging Grease This work aid is for providing backup to the seal while purging the head of grease. MSRP: Was: Now: $55.00 Add to Cart
206 Main Rotor Grease Catch Bottle Adapter Here is a tool that you will love. It turns a plastic bottle into a grease receptacle when you are purging the grip. Once you are finished, just throw away the bottle. Keeps from making a huge mess on top of the aircraft. No wiping/smearing needed... MSRP: Was: Now: $15.00 Add to Cart
206/407/505 Swashplate Roll Stake Bearing Work Aid Kit Bearing staking tool for the swashplate bearings. Allows you to perform the maintenance on the aircraft without removing the swashplate. T101530 MSRP: Was: Now: $250.00 - $3,000.00 Choose Options
Ultimate Swing Wrench Kit Ultimate Swing Wrench Kits contains 28 pieces. They are: T-handle, Screwdriver handle, and curved handle Open End: 1/4, 5/16, 3/8, 7/16, 1/2, & 9/16 Ratcheting Open End: 5/16 Regular Box End: 1/4, 5/16, 3/8, 7/16, 1/2, & 9/16 Ratcheting Box End:... MSRP: Was: Now: $1,750.00 Add to Cart
Spring Scale 0-50lbs 0-50 lbs Spring Scale. This spring scale is made of brass and will not shatter in your tool box like the cheap plastic spring scales. I've used both, brass and the plastic case spring scales. They both work. I just prefer the brass since they are a... MSRP: Was: Now: $110.00 Add to Cart
206/407/429/505 Adapter Wrench 206L - Freewheeling Unit 407 - Freewheeling Unit 429 - Clutch Assembly 505 - Transmission Input Seal Bell P/N T103306 MSRP: Was: Now: $335.00 Add to Cart
206 Trim Tab Bender Used to bend the trim tabs during track & balance. MSRP: Was: Now: $1,500.00 Add to Cart
Dykem Cross Check Torque Stripe We have this torque stripe in orange only MSRP: Was: Now: $10.00 Add to Cart
212/412/205 Tail Rotor Driveshaft Coupling Work Aid 212-412 Repack Tool C-shaped part used to be 3D printed. We have had feedback that the 3D printed part is breaking under pressure. Contact us if you need replacement. We will be sending out replacements soon. (June 10, 2024) MSRP: Was: Now: $180.00 Add to Cart
206 Mainrotor Head Sling Sling has a clear vinyl coating on the 1/4" cables. Cables are 6 feet long.Hooks have safety latches. Cable comes with inspection tag, serialized and weight certification.Included is a Certificate of Compliance/Test​Cable is rated at 2200 lbs. Each leg... MSRP: Was: Now: $210.00 Add to Cart
206 Lifting Clevis Lifting clevis for the 206 series (and now the 505). 204-011-178-001 MSRP: Was: Now: $1,850.00 Add to Cart
204/205/206/212/505 Pitch Horn Spreader Use it to spread the pitch horn and remove the trunnion fittings as per Bell Maintenance Manual. MSRP: Was: Now: $135.00 Add to Cart
206/505 Blade Pin Press No longer will you need to waste time with a stuck pin. Once you decide the pin is stuck, place the pin press around the grip with the large hole around the top of the pin. (The tool is upside down in the pictures) Reinstall the bottom plate (the... MSRP: Was: Now: $725.00 Add to Cart
206/505 Grip Lock Bolt - 2pcs Set Simplest, fastest, and best work aid to keep from scrapping a pair of TT Straps. Stronger and more reliable than T-handle type locks that most people use. MSRP: Was: Now: $78.00 Add to Cart
Bolt Extractor This work aid lets you apply pressure to the bolt while applying penetrating lube. Once the bolt pops loose it can easily be removed. Pressure is applied to the bolt and not to the tail boom fitting. Cracked fittings require tail boom removal at lots of... MSRP: Was: Now: $225.00 Add to Cart
206/505 Series Main Rotor Grip Locks - 2pcs set These lock tight, won't slip and are used to adjust the grips level when aligning and static balancing the main rotor. MSRP: Was: Now: $205.00 Add to Cart
Reversible Swing Wrenches These reversible swing wrenches are an improvement over our other wrenches. We are using the reversible Gear wrench brand so when you get into a tight spot and can't get the wrench off the nut or bolt you can simply flip the reversing lever and back out... MSRP: Was: Now: $95.00 - $105.00 Choose Options
Brass Screwdriver For Compass Adjustment No more trying to make a screw driver for adjusting compasses with a hammer and welding rod.This is a quality, solid brass screwdriver made especially for adjusting compasses.It's 4 3/4 inches long and the blade tip is 5/32" wide. MSRP: Was: Now: $23.00 Add to Cart
206/407/505 Oil Cooler Blower Driveshaft Spanner Wrench Wrench to get off the spanner nut on the oil cooler blower. The L-model wrench will also work on the 407. MSRP: Was: Now: $70.00 Add to Cart
206 Knurl Nut Wrench This will easily remove that stuck knurl nut. It is especially great if you want to replace the knurl nut liner and don't want to ruin the knurl nut with channel locks because the knurl nut is frozen. MSRP: Was: Now: $130.00 Add to Cart
Grease Fitting - Straight These are the threaded ones, not the quick disconnect ones that get grease everywhere except the part you want it in. MSRP: Was: Now: $15.00 Add to Cart
Grease Fitting - 90° These are the threaded ones, not the quick disconnect ones that get grease everywhere except the part you want it in. MSRP: Was: Now: $20.00 Add to Cart
90° Grease Coupler I recently found this 90 degree grease coupler that works great on hard to access grease fittings.Works really well on the oil cooler blower bearings on the Bell 407. It slides in from the side when straight on access is difficult or next to impossible. MSRP: Was: Now: $16.00 Add to Cart
Swashplate Shim Alignment Studs Holds the shims in position when doing the swashplate friction check. The hex head is 5/32" drive.An allen wrench is easier to get in to tight areas than a long phillips screwdriver. Can also be used as jack screws on the 206 and 407 transmission input... MSRP: Was: Now: $20.00 Add to Cart
206L Tach Generator Driveshaft Removal & Installation Work Aid Work aid to remove and replace tach generator driveshaft as seen in figure 63-7c MSRP: Was: Now: $125.00 Add to Cart
206 Main Rotor Hub Pitch Horn Lock Use this work aid when lifting the hub assembly from the mast. Remove upperside of pitch control links and install the work aid. MSRP: Was: Now: $425.00 Add to Cart
206 Swashplate Uniball Lower Bushing Remover Removes lower bushings from swashplate uniball. MSRP: Was: Now: $55.00 Add to Cart
Torque Adapters 1/4" Drive Hard to find 1/4" drive torque adapters. Most torque adapters you will find are 3/8" drive. These will allow you to use that low torque 1/4" torque wrench without the 3/8" to 1/4" adapter. SAE: The standard set consists of 1/4", 5/16", 3/8", &... MSRP: Was: Now: $50.00 - $170.00 Choose Options
Bell 429 & 505 Live Mount Gauge Pressure gauge in 2 psi increments (as per Bell Maintenance Manual) to calibrate live mounts on 429 and 505.Disclaimer: The manufacturer of the gauge will not warranty any gauge shipped out of the continental U.S. I can furnish a... MSRP: Was: Now: $575.00 Add to Cart
Bell 505 Tail Boom Rigging Pin - 143 ​Required for rigging the tailboom on the 505. 427-201-001-143 MSRP: Was: Now: $85.00 Add to Cart
Bell 505 Tail Boom Rigging Pin - 147 ​Required for rigging the t/boom on the 505. 427-201-001-147 MSRP: Was: Now: $85.00 Add to Cart
505 Free Wheeling Unit Drain Hose The freewheeling unit chip plug on the 505 sits in a pan assembly that requires an extra short drain fitting because of clearance issues. The position also requires a suction pump to pull the oil out of the freewheeling unit assembly. It just won't... MSRP: Was: Now: $145.00 Add to Cart
Air Conditioner Belt Tensiometer Belt Tensiometer specified by Bell for checking air conditioning belt tension. Scale reads in pounds and kilograms Measures tension from 30 to 160 lb., and 15 to 75 kg. Die-cast aluminum body, nylon indicator arm and pressure pad Fits in pocket... MSRP: Was: Now: $30.00 Add to Cart
Oil Can Opener One Black Plastic "Church Key" FOD Free Turbine Oil Can Opener MSRP: Was: Now: $7.00 Add to Cart
ENGWASH-HF-BRACKET This is just the brackets and fasterners necessary to attach your (ENGWASHx2) double engine wash bottle set up to a Harbor Fright Welding Cart. Purchase your own Welding Cart from Harbor Freight and use these brackets to fasten them to the... MSRP: Was: Now: $300.00 Add to Cart
Swashplate Gimbal Ring Bolt Removal Workaid (204B, 205, 212 & 412) Swashplate Gimbal Ring Bolt Removal Workaid (204B, 205, 212 & 412) 204B-22-27 205-22-45 205B-22-29 212-22-74 412-22-93 MSRP: Was: Now: $300.00 Add to Cart
206 & 505 Main Rotor Blade Alignment Pins - 2pcs Easier and faster than mirrors and cheaper than a laser.No calibration needed. Drop it in the bolt hole and set the string. 206-MR-F-06 MSRP: Was: Now: $115.00 - $145.00 Choose Options
206/505 Tail Rotor Rigging Flap Lock Work Aid Bell designed flap lock for 206/505. These were acquired through purchase of HeliTools inventory. Limited supply. See our design here. MSRP: Was: Now: $25.00 Add to Cart
Bell 505 Portable Hydraulic Pump Drive Unit Portable Hydraulic Pressure Drive Unit for Bell 505. Due to the tight work space where the hydraulic pump is located, the unit comes with hydraulic hoses to be able to remove the hyd pump from the aircraft and move it away from the tight work area... MSRP: Was: Now: $4,750.00 Add to Cart
Bell 505 CORDLESS Portable Hydraulic Pump Drive Unit Portable CORDLESS Hydraulic Pressure Drive Unit for Bell 505. Due to the tight work space where the hydraulic pump is located, the unit comes with hydraulic hoses to be able to remove the hyd pump from the aircraft and move it away from... MSRP: Was: Now: $4,900.00 Add to Cart
206B/L/505 Main Rotor Static Balance Kit Static Balancing Kit for 206B/L and 505. Comes in protective case with extra plastic bin to store lead weights. This is from Chuck Dugan from Helitools. We acquired his inventory. Contact us for any other tools that was previously supplied by... MSRP: Was: Now: $4,900.00 Add to Cart
