Rolls-Royce 250 HMU "Fuel Control" Throttle/Fly Detent Rigging Pin MSRP: Was: Now: $45.00 Add to Cart
Rolls-Royce 250 Starter/Generator Seal Installer & Fuel Pump Seal Installer - 2pcs MSRP: Was: Now: $145.00 Add to Cart
RR250 C20/30/47 Engine Sled Made to fit the C20/C30/C47. Easy assembly and disassembly for shipping. Rolls-Royce P/N 6891189 MSRP: Was: Now: $900.00 Add to Cart
Rolls-Royce 250 Spur Adapter Gear Installation Work Aid P/N: 250SG2 (C20 only) Rolls-Royce P/N 23006778 P/N 250SG3 (C30 & C47) Rolls-Royce P/N 23005426 MSRP: Was: Now: $240.00 Choose Options
RR250 Accessory Drive Lip Seal Installs the Starter/Generator and HMU (Fuel Pump) seals on the C47 gearbox MSRP: Was: Now: $140.00 Add to Cart
Engine Wash Bottle SINGLE BOTTLE: This is a stainless, 2 1/2 gallon bottle that has been used by all the major operators in the Gulf of Mexico for the last 45 years to my knowledge. I have replaced the short stock hose with 7 ft of high quality chemical resistant... MSRP: Was: Now: $325.00 - $815.00 Choose Options
Rolls-Royce 250 Fuel Nozzle Shimming Gauge The simplest gauge for calculating the required shims for the fuel nozzle! We provide instructions that are for reference, but as usual, refer to maintenance manual for latest information. We also have an excel spreadsheet to make... MSRP: Was: Now: $275.00 - $370.00 Choose Options
Rolls-Royce 250 C47 Ratcheting Open-End Fuel-Control Swing Wrench Ratcheting open end swing wrench designed to remove that pesky upper 5/16 nut on the fuel control. With a slow and steady control of the swing wrench, I was able to remove the upper nut in approximately three minutes. Compare that to the last time you... MSRP: Was: Now: $85.00 Add to Cart
Rolls-Royce 250 Turbine To Gearbox Attach Bolt Wrenches - 3pcs No longer will you need to use that calibrated elbow. We have designed 3 wrenches to perform the torque checks on the 6 turbine to gearbox attach bolts on the RR250-C30 and C47 engines. A long 1/4" extension will be required to torque the bolt above the... MSRP: Was: Now: $120.00 Add to Cart
Rolls-Royce 250 C30/C47 Fuel Nozzle Wrench This fuel nozzle wrench is double sided to give you better access to the fuel nozzle. With the cowling installed, if you place the wrench on the fuel nozzle, it may not sit the way you want because of the limited space, flip it to the other side. The... MSRP: Was: Now: $125.00 Add to Cart
Rolls-Royce 250 C30/C47 Medium Fuel Nozzle Wrench This wrench is usually preferred by the overhaul guys working the engine on a stand. MSRP: Was: Now: $95.00 Add to Cart
Rolls-Royce 250-C20/C30/C47 Engine Lifting Eye Engine lifting eye for C20, C30, and C47. Long enough to clear the exhaust stack so it doesn't have to be removed. Rolls-Royce C20 6796963Rolls-Royce C30/C47 6889888 MSRP: Was: Now: $475.00 Add to Cart
Rolls-Royce 250 Ignitor Wrench Ignitors can be hard to remove for several reasons. Someone put it in too tight, didn't use anti-seize or used a 12 point socket and slipped, rounding off the corners. This wrench is made from a 6 point impact socket. Install the wrench and put the... MSRP: Was: Now: $65.00 Add to Cart
Rolls-Royce 250 Starter/Generator Spline Turn Wrench T-handle wrench for turning the N1 wheels while doing maintenance on the RR250 series engines. Starter/generator splines are hard to find, so get yours here Rolls-Royce P/N 6799790 MSRP: Was: Now: $55.00 Add to Cart
Rolls-Royce 250 Exhaust Stack Wrench Wrench is made for removal of the nuts on the exhaust stack. Keeps nuts from falling into crevices of the engine. MSRP: Was: Now: $30.00 Add to Cart
Jackscrews 1/4" 28 - 3pcs Use these on transmission input quills, freewheeling unit, tailrotor gearbox, or any component requiring 1/4" 28 jackscrews. T101308 MSRP: Was: Now: $75.00 Add to Cart
Rolls-Royce 250 C30/C47 Gearbox PTO Seal Installer This installer works on the C30 and C47 engines. You can install one seal at a time or both at once. This is the best seal installer you will find for the gearbox seals. MSRP: Was: Now: $825.00 Add to Cart
Rolls-Royce 250 C30/C47 Gearbox PTO Seal Remover Removes rear gearbox seal. MSRP: Was: Now: $725.00 Add to Cart
Rolls-Royce 250 C30/C47 Bleed Valve Shop Air Adapter Quick disconnect so that you can use shop air to close the Bleed valve. MSRP: Was: Now: $40.00 Add to Cart
Rolls-Royce 250 Quick Disconnect Coupling For Engine Rinse Name says it all. MSRP: Was: Now: $45.00 Add to Cart
Rolls-Royce 250 Power Turbine Support Cleaning Kit Kit comes in a foam insert for easy storage and handling. Keep the cardboard box it comes in for added protection. RR P/N 23007615 MSRP: Was: Now: $175.00 Add to Cart
RR250 C30/C47 Compressor/Diffuser Orifice R&R Work Aid Use this work aid to remove and re-install the orifice when it is located in the exhaust collector.Good on any 206L with C30 installed, 407, and Sikorsky S-76A. MSRP: Was: Now: $85.00 Add to Cart
Rolls-Royce 250 C47 Engine Gearbox Drain As you know, the C47 has the quick disconnect chip detectors that have the self plugging housing. Unlike the C30's that will drain when you pull the chip detectors, the C47 requires this work aid to drain the gearbox. This drain is made from steel. MSRP: Was: Now: $105.00 Add to Cart
Rolls-Royce 250 HMU "Fuel Control" Throttle/Fly Detent Rigging Pin Easy to handle rigging pin with red streamer. MSRP: Was: Now: $45.00 Add to Cart
Rolls-Royce 250 Oil Pressure Regulator Socket 1/4 inch drive socket for adjusting the oil pressure regulator.Makes it easy to adjust and count the turns plus it won't eat up the regulator adjusting bar when using needle nose pliers like other people used to do. MSRP: Was: Now: $45.00 Add to Cart
Rolls-Royce 250 Turbine Wheel Lock Used to lock the turbine wheel in place when installing the turbine section. The plate and rod are made from brass. The brass rod is soft enough to bend if necessary so it won't damage the turbine blades should excessive pressure be applied to the... MSRP: Was: Now: $65.00 Add to Cart
Rolls-Royce 250 Starter/Generator Seal Installer & Fuel Pump Seal Installer - 2pcs This work aid is a 2 in 1. Use it on either the starter/generator seal or the fuel pump seal. Simplifies installation of seals and removes chances of damaging seal while installing. This work aid is only for lip seal (23079054). MSRP: Was: Now: $145.00 Add to Cart
C30/47 #1 Bearing in Compressor Puller C30/47 #1 Bearing in Compressor Puller 23005023 MSRP: Was: Now: $850.00 Add to Cart
