BELL-407

407 Main Rotor Blade Tie Down (4pc Set)

Four piece set of main rotor blade tie downs.

407 Pitch Change Link Protective Maintenance Covers

Straight from the maintenance manual: EXERCISE CAUTION WHEN SUPPORTING THE PITCH LINK TUBE TO MAKE SURE THAT YOU DO NOT SCRATCH OR DISTORT THE TUBE. FAILURE TO DO SO MAY DAMAGE THE PART. By request of a few customers, here they are. Color coded...

407 Pitch Change Universal Bearing PITA Grease Fitting Work Aid

Here it is boys and girls. Finally a tool to grease that one pain in the ass grease fitting. No longer will you have to remove the pitch link just to grease the bearing in all 4 spots. Now even your pilot can complete the 50 hour lube. This grease...

407 Main Rotor Hub Overhaul Work Aid Kit

10X Magnifying Glass

We chose this model of magnifying glass because the cup is setup for the correct focal distance. Just place the magnifying glass on the object you are trying to inspect and you are focused. No fighting the loupe trying to figure out the correct focus...

206/407 Intake Plugs and Exhaust Cover

Intake plugs come with pitot cover attached together. Your pilot will have to lose the plugs to be able to lose the pitot cover.

407 Main Rotor Hub Assembly Adapter

Adapter is used to maintain alignment of main rotor hub assemblies during teardown and re-assembly for overhaul.   Bell 407-210-005-101

Composite Tap Hammer

Use the tap hammer on main rotor blades or any other composite material to check for delamination.   You can order somewhere else for $15 + $12 shipping ($27 total) or just bundle with your next order with us.   Equivalent to T75449-2

Swashplate Shim Alignment Studs

Holds the shims in position when doing the swashplate friction check. The hex head is 5/32" drive.An allen wrench is easier to get in to tight areas than a long phillips screwdriver. Can also be used as jack screws on the 206 and 407 transmission input...

407 Lifting Clevis

T102137-107 T102137-111​Not much to say about this item. I think everyone knows what it's for.

407 Pitch Link Tension Reliever

Used to move the blade and grip when trying to re-connect the pitch change links.

407 Expandable Blade Bolt Inspection Work Aid

Expandable blade bolts require 600 hour or 12 month inspection. Those inspections require removing the segments on the expandable bolts and inspecting for corrosion and wear. This work aid assists by maintaining all the segments in the proper order...

407 Main Rotor Pitch Change Link Trammel

Trammel made especially for the 407 main rotor pitch change link. Trammel adjusts to fit the old link.Pull the round pin out and install the new link.Adjust the new link until the round pin slides back into the hole. Tighten the link jam nuts and...

407 Torque Reactor Pin

Used with your choice of a 4-1 or 3-1 torque multiplier. 407 back up pin in use. Let the torque multiplier bump up against the pin to hold backup.This pin lets you do the mast nut torque or 1-5 hr torque check by yourself not to mention holding...

407 Blade Bolt Bullets

Never fight with the main rotor blade again! With these bullets you can get the blade mostly in place and just push the bolts through! The bullets keep the shoulders of the bolt from catching. The new guy you have leaning off a ladder, holding up the...

407 Frahm Cover Bit

This is the apex bit for the 407 Frahm cover. Everybody on the crew needs one and this is where you can find them.

407 Main Rotor Assy Alignment Guide and Thread Protector

Threads on to the end of the mast to act as a guide for installation and also protects the mast nut threads during maintenance.

407 Main Rotor Head Sling

Sling for removing rotor head. Blades should not be installed when rotor head is being removed. Picture shows sling in use.If you are using the guide and mast thread protector a longer strap is required. Let us know if you are using the thread protector...

407 Main Rotor 1-1/4" Mast Nut Socket

1-1/4 impact socket for the Main Rotor Mast Nut. 3/4" and 1" drive available  

407 Swashplate Overhaul - 23pcs set

​Consists of 23 pieces for overhaul of the 407 swashplate as per CR&O

407 Main Rotor Hub Assembly/Dis-assembly Work Aid - 5pcs set

Contact us for individual piece pricingWork aid for assembly and dis-assembly of the mainrotor hub.  Fig 62-4 Items 3, 8, 9, 10

407 Main Rotor Mast Nut Torque Kit

This kit includes everything you need to torque the mast nut on the 407 main rotor except for the 600 lb torque wrench. It has a 3-1 torque multiplier, the torque reactor pin to hold a back up and the 1 1/4" 1 inch drive impact socket.​It...

407 Main Rotor Mast Nut Torque Kit With Torque Wrench

This kit includes everything you need to torque the mast nut on the 407 main rotor including the 600 lb torque wrench made by Performance Tool. These are very good quality wrenches. It has a 3-1 torque multiplier, the torque reactor pin to hold...

407 Torque Multiplier Fixture

P/N 407TMF-HT   Used with your choice of a 4-1 or 3-1 torque multiplier.  Let the torque multiplier bump up against the pin to hold backup.This fixture lets you do the mast nut torque or 1-5 hr torque check by yourself not to mention...

407 Trim Tab Bender

Used to make adjustments on main rotor trim tabs during tracking.  Comes with protective case.  Bell P/N T103316 & T103317