Rolls-Royce 250-C20 Starter/Generator & Fuel Pump Seal Installer MSRP: Was: Now: $135.00 - $165.00 Choose Options
Rolls-Royce 250 Starter/Generator Seal Installer & Fuel Pump Seal Installer - 2pcs MSRP: Was: Now: $145.00 Add to Cart
Rolls-Royce 250 Spur Adapter Gear Installation Work Aid P/N: 250SG2 (C20 only) Rolls-Royce P/N 23006778 P/N 250SG3 (C30 & C47) Rolls-Royce P/N 23005426 MSRP: Was: Now: $240.00 Choose Options
Rolls-Royce 250 C20 Compressor Case Half Wrenches - 3pcs set With these wrenches, you can now cut down the time it takes to disassemble the case halves by 50%. Bits are removable which allows you to use the reverse side of the ratchet for removal and installation with just our two ratcheting wrenches. Comes with a... MSRP: Was: Now: $540.00 Add to Cart
Rolls-Royce 250 C20 Gearbox Seal Installer Installs the gearbox seals on the C20's. Place guide on output shaft, place seal over the guide, and place flange over the seal. MSRP: Was: Now: $300.00 Add to Cart
Rolls-Royce 250-C20/C30/C47 Engine Lifting Eye Engine lifting eye for C20, C30, and C47. Long enough to clear the exhaust stack so it doesn't have to be removed. Rolls-Royce C20 6796963Rolls-Royce C30/C47 6889888 MSRP: Was: Now: $475.00 Add to Cart
Jackscrews 1/4" 28 - 3pcs Use these on transmission input quills, freewheeling unit, tailrotor gearbox, or any component requiring 1/4" 28 jackscrews. T101308 MSRP: Was: Now: $75.00 Add to Cart
Rolls-Royce 250 C30/C47 Gearbox PTO Seal Installer This installer works on the C30 and C47 engines. You can install one seal at a time or both at once. This is the best seal installer you will find for the gearbox seals. MSRP: Was: Now: $825.00 Add to Cart
Rolls-Royce 250 C30/C47 Gearbox PTO Seal Remover Removes rear gearbox seal. MSRP: Was: Now: $725.00 Add to Cart
Rolls-Royce 250 Power Turbine Support Cleaning Kit Kit comes in a foam insert for easy storage and handling. Keep the cardboard box it comes in for added protection. RR P/N 23007615 MSRP: Was: Now: $175.00 Add to Cart
Rolls-Royce 250-C20 Starter/Generator & Fuel Pump Seal Installer This is the new seal installer from Rolls-Royce's Commercial Service Letter. This was designed for installing the new lip seals (23091467) which include a supplied installation mandrel.Although it will also work on the old lip seals (23079054) we,... MSRP: Was: Now: $135.00 - $165.00 Choose Options
Rolls-Royce 250 Turbine Wheel Lock Used to lock the turbine wheel in place when installing the turbine section. The plate and rod are made from brass. The brass rod is soft enough to bend if necessary so it won't damage the turbine blades should excessive pressure be applied to the... MSRP: Was: Now: $65.00 Add to Cart
Rolls-Royce 250 St. Gobain PTO Seal Installer These are the seal installers for the new St Gobain seals p/n 23091293 (red) and p/n 23091353 (blue)They can also be used for installing the Viton SealsThe C20 and C30/47 have different seal insertion depths so order according to your engine model MSRP: Was: Now: $275.00 Choose Options
RR250-C30/C47 Spur Adapter Gear O'ring Installation Work Aid For engines C30 and C47 only RR P/N 23006785 MSRP: Was: Now: $410.00 Add to Cart
Rolls-Royce 250 Starter/Generator Seal Installer & Fuel Pump Seal Installer - 2pcs This work aid is a 2 in 1. Use it on either the starter/generator seal or the fuel pump seal. Simplifies installation of seals and removes chances of damaging seal while installing. This work aid is only for lip seal (23079054). MSRP: Was: Now: $145.00 Add to Cart
Rolls-Royce 250 PTO Seal Remover Used to remove single lip PTO seal on RR250 engines. Thread into the seal and use slide hammer to remove. MSRP: Was: Now: $525.00 Add to Cart
C30/47 #1 Bearing in Compressor Puller C30/47 #1 Bearing in Compressor Puller 23005023 MSRP: Was: Now: $850.00 Add to Cart
