206/505 Transmission & Tail Rotor Gearbox Input Pinion Remover MSRP: Was: Now: $550.00 - $1,450.00 Choose Options
206/407/505 Transmission Oil Pump Accessory Gear Drive Spanner Nut Socket MSRP: Was: Now: $290.00 Add to Cart
Swashplate Gimbal Ring Bolt Removal Workaid (204B, 205, 212 & 412) MSRP: Was: Now: $300.00 Add to Cart
206/407/505 Freewheeling Unit Shaft Removal Work Aids MSRP: Was: Now: $150.00 - $450.00 Choose Options
206/505 Mast Assembly Overhaul Kit Kit contains all special tools to complete 206 mast overhaul as per CR&O. MSRP: Was: Now: $2,260.00 Add to Cart
206/407/505 Transmission Accessory Bevel Gear Bearing Work Aid Used to hold the accessory drive gear while applying torque to the gearshaft spanner nut. Bell P/N T101504 MSRP: Was: Now: $450.00 Add to Cart
407 Freewheeling Assembly Seal Installation/Removal Tool This tool is used to both remove and install the seal from the freewheeling shaft nut. Bell P/N T103307 MSRP: Was: Now: $500.00 Add to Cart
206/505 Transmission & Tail Rotor Gearbox Input Pinion Remover 206/505 Transmission And Tail Rotor Gearbox Input Pinion Remover Bell P/N T101507 MSRP: Was: Now: $550.00 - $1,450.00 Choose Options
206/407/429/505 Adapter Wrench 206L - Freewheeling Unit 407 - Freewheeling Unit 429 - Clutch Assembly 505 - Transmission Input Seal Bell P/N T103306 MSRP: Was: Now: $335.00 Add to Cart
205/206/212/407/412/505 Transmission Planetary Install Pin This pin is used in removing or installing planetary pinions or the spur gear in the planetary assemblies. Helitools P/N 206-XMSN-OH-10 Bell P/N T101332 MSRP: Was: Now: $75.00 Add to Cart
205/206/212/407/412/505 Transmission Planetary Guide Shaft This work aid is used in aligning the pinion assembly inner race during removal and installation of the retaining shaft in lower planetary housing. Helitools P/N 206-XMSN-OH-11 Bell P/N T101574 MSRP: Was: Now: $400.00 Add to Cart
206/407/505 Transmission Accessory Gear Backlash Work Aid Used to check backlash between the transmission main input gear and the accessory drive gear. Helitools P/N 206-XMSN-OH-07 Bell P/N T101735 MSRP: Was: Now: $1,500.00 Add to Cart
206L/505 Transmission Holding Fixture And Spline Wrench Set Fixture to hold the 206 L-model and 505 transmission during repair and overhaul. Helitools P/N 206-XMSN-OH-08L Bell P/N T101883 MSRP: Was: Now: $2,800.00 Add to Cart
206 Mast Spline Overhaul Wear Pins These are the .080 and .160 wear pins the manual calls out for to do the checks on the mast splines during overhaul. This set comes with 2ea .0800" and 2ea .1600" pins. Click here for a selection of different size pins MSRP: Was: Now: $46.00 Add to Cart
206/505 Transmission Duplex Bearing Nut Wrench Used on the duplex bearing retainer nut. Helitools P/N 206-XMSN-OH-02 Bell P/N T101501 MSRP: Was: Now: $1,500.00 Add to Cart
206/505 Mast V-Block These are the 4inch V-Blocks the maintenance manual calls for to do mast inspections/overhauls. It is a 2 piece set. It also doubles as an amazing paperweight. (Tested and approved) Helitools P/N 206-MAST-F-04 MSRP: Was: Now: $250.00 Add to Cart
206/505 Mast Assembly Nut Wrench Wrench is used to remove and torque the nut on the mast assembly during overhaul. Helitools P/N 206-MAST-F-02 Bell P/N T102040 MSRP: Was: Now: $650.00 Add to Cart
206/505 Mast Holding Fixture (Alternate) Used to hold the mast assembly when torque is applied to the ball bearing retaining nut during removal and installation. Helitools P/N 206-MAST-F-01 Bell P/N T101499 CLICK HERE FOR 206-240-002-101 MSRP: Was: Now: $800.00 Add to Cart
206/505 Transmission Backlash Work Aid This item is used to check the backlash between the main input pinion gear and the input driven bevel gear. CR&O has all the details. The base plate is NOT included. Click here for the baseplate Helitools 206-XMSN-OH-05 Bell... MSRP: Was: Now: $900.00 Add to Cart
206/407/505 Freewheeling Unit Cap Restraint Fixture Fixture used to hold freewheeling unit cap on vice while doing maintenance Helitools P/N 206-FWU-OH-11 Bell P/N T103308 MSRP: Was: Now: $475.00 Add to Cart
206/407/429/505 Freewheeling Unit Bearing Installation Sleeve For pressing the roller bearing during freewheeling unit maintenance. For the "clutch" on the 429. Helitools 206-FWU-OH-16 Bell T103332 MSRP: Was: Now: $90.00 Add to Cart
206/407/505 Transmission Oil Pump Accessory Gear Drive Spanner Nut Socket Socket specifically designed for the spanner nut on the accessory gear that drives oil pump. Maintenance manual calls out for AN8515-1 Spanner Wrench. Our socket is a better design that won't slip and make you bust your knuckles. MSRP: Was: Now: $290.00 Add to Cart
Bell 429 & 505 Live Mount Gauge Pressure gauge in 2 psi increments (as per Bell Maintenance Manual) to calibrate live mounts on 429 and 505.Disclaimer: The manufacturer of the gauge will not warranty any gauge shipped out of the continental U.S. I can furnish a... MSRP: Was: Now: $575.00 Add to Cart
505 Free Wheeling Unit Drain Hose The freewheeling unit chip plug on the 505 sits in a pan assembly that requires an extra short drain fitting because of clearance issues. The position also requires a suction pump to pull the oil out of the freewheeling unit assembly. It just won't... MSRP: Was: Now: $145.00 Add to Cart
Oil Can Opener One Black Plastic "Church Key" FOD Free Turbine Oil Can Opener MSRP: Was: Now: $7.00 Add to Cart
Swashplate Gimbal Ring Bolt Removal Workaid (204B, 205, 212 & 412) Swashplate Gimbal Ring Bolt Removal Workaid (204B, 205, 212 & 412) 204B-22-27 205-22-45 205B-22-29 212-22-74 412-22-93 MSRP: Was: Now: $300.00 Add to Cart
206/505 Transmission Bearing Installation and Removal Plug P/N 206XBS-HT Used to support the input driven spiral bevel gearshaft duplex bearing by the outer race while pressing bearing into or out of the transmission lower case. T101503 206-XMSN-OH-25 MSRP: Was: Now: $725.00 Add to Cart
206/505 Transmission Gear Shaft Nut Wrench Used to apply torque to the input driven spiral bevel gearshaft duplex bearing outer ring retaining nut. Bell P/N T101502 Helitools' P/N 206-XMSN-OH-03 MSRP: Was: Now: $225.00 Add to Cart
206/505 Mast Holding Fixture Used to hold the mast assembly when torque is applied to the ball bearing retaining nut during removal and installation. Bell P/N 206-240-002-101 Helitools P/N 206-MAST-F-05 CLICK HERE FOR T101499 MSRP: Was: Now: $850.00 Add to Cart
206 Planetary Shaft Sleeve Used to remove aand install the planet gear shaft from and into the arm of the spider and the bearing assembly inner race. T101506 206-XMSN-OH-20 MSRP: Was: Now: $525.00 Add to Cart
206/407/505 Freewheeling Unit Wrench Used to remove and install the 214-040-241 nut. This tool replaces wrench assembly 407-240-006-101. 206-FWU-OH-18 T101960 MSRP: Was: Now: $150.00 Add to Cart
206/505/407 Freewheeling Unit Duplex Bearing Removal Driver Used to remove the 406-040-531 bearing from the 406-040-508 Cap Assembly. 206-FWU-OH-15 T103324-101 MSRP: Was: Now: $250.00 Add to Cart
206/407/505 Freewheeling Unit Bearing Installation Sleeve Used to install the 206-040-206 bearing into the 406-040-516 shaft. 206-FWU-OH-17 T103333 MSRP: Was: Now: $90.00 Add to Cart
206/407/505 Freewheeling Unit Shaft Removal Work Aids Used in conjuction with a press to remove the shaft from the bearing. T103310-101 MSRP: Was: Now: $150.00 - $450.00 Choose Options
Oil Collector Pan - Alignment Pilot Workaid Oil Collector Pan - Alignment Pilot Workaid for top case 206-040-550 Figure 63-19 MSRP: Was: Now: $250.00 Add to Cart
Oil Collector Pan - Alignment Pilot Work aid Oil Collector Pan - Alignment Pilot Work aid for top case 206-040-532 Figure 63-19 MSRP: Was: Now: $250.00 Add to Cart
Oil Collector Pan - Alignment Pilot Work Aid Set Oil Collector Pan - Alignment Pilot Work Aid Set For top case 206-040-550 & 206-040-532 Figure 63-19 MSRP: Was: Now: $450.00 Add to Cart
