206/407/505 Swashplate Roll Stake Bearing Work Aid Kit MSRP: Was: Now: $250.00 - $3,000.00 Choose Options
206/407/505 Swashplate Roll Stake Bearing Work Aid Kit Bearing staking tool for the swashplate bearings. Allows you to perform the maintenance on the aircraft without removing the swashplate. T101530 MSRP: Was: Now: $250.00 - $3,000.00 Choose Options
Spring Scale 0-50lbs 0-50 lbs Spring Scale. This spring scale is made of brass and will not shatter in your tool box like the cheap plastic spring scales. I've used both, brass and the plastic case spring scales. They both work. I just prefer the brass since they are a... MSRP: Was: Now: $110.00 Add to Cart
ASB 407-23-130 Pilot Cyclic Stick Stop-Drill Work Aid Work aid for ASB 407-23-130 to stop drill cracks on the cyclic stick. 1st drill bushing of .070" listed on ASB not available, Comes with 3 removeable drill bushings and 3 drill bits. #40 .098" #30 .1285" 3/16" ... MSRP: Was: Now: $275.00 Add to Cart
Bolt Extractor This work aid lets you apply pressure to the bolt while applying penetrating lube. Once the bolt pops loose it can easily be removed. Pressure is applied to the bolt and not to the tail boom fitting. Cracked fittings require tail boom removal at lots of... MSRP: Was: Now: $225.00 Add to Cart
Bypass Spool Check Mount - With Dial Indicator Bracket held on with nylon screws so as not to damage the servo anodized surface.The bracket also comes with a powder coat finish which gives additional protection to the anodized finish on the servo. MSRP: Was: Now: $2.00 - $255.00 Choose Options
Swashplate Shim Alignment Studs Holds the shims in position when doing the swashplate friction check. The hex head is 5/32" drive.An allen wrench is easier to get in to tight areas than a long phillips screwdriver. Can also be used as jack screws on the 206 and 407 transmission input... MSRP: Was: Now: $20.00 Add to Cart
Torque Adapters 1/4" Drive Hard to find 1/4" drive torque adapters. Most torque adapters you will find are 3/8" drive. These will allow you to use that low torque 1/4" torque wrench without the 3/8" to 1/4" adapter. SAE: The standard set consists of 1/4", 5/16", 3/8", &... MSRP: Was: Now: $50.00 - $170.00 Choose Options
407 Pitch Link Tension Reliever Used to move the blade and grip when trying to re-connect the pitch change links. MSRP: Was: Now: $285.00 Add to Cart
407 Main Rotor Pitch Change Link Trammel Trammel made especially for the 407 main rotor pitch change link. Trammel adjusts to fit the old link.Pull the round pin out and install the new link.Adjust the new link until the round pin slides back into the hole. Tighten the link jam nuts and... MSRP: Was: Now: $480.00 Add to Cart
407 Collective Pitch Transducer Work Aid Work aid to help rig the collective pitch transducer. MSRP: Was: Now: $35.00 Add to Cart
407 Swashplate Overhaul - 23pcs set ​Consists of 23 pieces for overhaul of the 407 swashplate as per CR&O MSRP: Was: Now: $50.00 - $2,385.00 Choose Options
407 Swashplate Shipping Plate Color varies when manufactured Protects swashplate and uniball from getting bounced around and beat up during shipping. MSRP: Was: Now: $55.00 Add to Cart
407 Trim Tab Bender Used to make adjustments on main rotor trim tabs during tracking. Comes with protective case. Bell P/N T103316 & T103317 MSRP: Was: Now: $2,300.00 Add to Cart
