Shop by Make & Model

Rolls-Royce 250/300 St. Gobain Seal Remover

Slide hammer to remove the St Gobain seal on both the RR250 and RR300.

Rolls-Royce 250 Engine Maintenance Stand

Maintenance stand that can rotate engine 360 degrees. Maintenance stand can be taken apart for transportation or storage. Transportation/Shipping case is Made In America by Condition 1. P/N is 2191

S70/UH-60 Hot Section Engine Wash

Harness to complete engine wash on the Blackhawk 1226-410KT

407 Kaflex Work Aid

Here it is, the tool you all have been wanting from us for a while.    Ours is made with solid bolts so you don't have the issues that the cables give you   Red cover is to protect kaflex shaft during maintenance and while sitting on the...

Rolls-Royce C30 Bleed Valve Wrench

C30 Bleed Valve Wrench. This was designed for the MD500 guys who are working in a much tighter space than the 206 guys.

Rolls-Royce 250 Fuel Nozzle Holding Fixture

Another one where the name of the tool describes it beautifully. Rolls-Royce P/N 6897875

Rolls-Royce 250 Starter/Generator Seal Remover

Special slide hammer tool used to remove the seal from the starter/generator.

Oil Can Dust Cap

Instead of using a latex glove, we have all seen it, you can now save that half used can of oil with these caps specifically made for the quart cans. The Dust Cap protects your oil cans against dust, dirt and debris It saves money on leftover oil,...

Magnetic Seal Installation/Removal Work Aid

8814163000

RR250 C20/30/47 Engine Sled

Made to fit the C20/C30/C47. Easy assembly and disassembly for shipping. Rolls-Royce P/N 6891189

Rolls-Royce 250 Spur Adapter Gear Installation Work Aid

P/N: 250SG2 (C20 only) Rolls-Royce P/N 23006778   P/N 250SG3 (C30 & C47) Rolls-Royce P/N 23005426

RR250 Accessory Drive Lip Seal

Installs the Starter/Generator and HMU (Fuel Pump) seals on the C47 gearbox

Engine Wash Bottle

SINGLE BOTTLE: This is a stainless, 2 1/2 gallon bottle that has been used by all the major operators in the Gulf of Mexico for the last 45 years to my knowledge.  I have replaced the short stock hose with 7 ft of high quality chemical resistant...

407 Kaflex Mounting Wrench

If you have ever installed a Kaflex drive shaft, you know how its practically impossible to actually torque them. We designed these wrenches so you could stop using that calibrated elbow and properly torque them with a torque wrench.

Rolls-Royce 250 Fuel Nozzle Shimming Gauge

The simplest gauge for calculating the required shims for the fuel nozzle!  We provide instructions that are for reference, but as usual, refer to maintenance manual for latest information.   We also have an excel spreadsheet to make...

Rolls-Royce 250 C47 Ratcheting Open-End Fuel-Control Swing Wrench

Ratcheting open end swing wrench designed to remove that pesky upper 5/16 nut on the fuel control. With a slow and steady control of the swing wrench, I was able to remove the upper nut in approximately three minutes. Compare that to the last time you...

Rolls-Royce 250 C20 Compressor Case Half Wrenches - 3pcs set

With these wrenches, you can now cut down the time it takes to disassemble the case halves by 50%. Bits are removable which allows you to use the reverse side of the ratchet for removal and installation with just our two ratcheting wrenches. Comes with a...

Rolls-Royce 250 C20 Gearbox Seal Installer

Installs the gearbox seals on the C20's. Place guide on output shaft, place seal over the guide, and place flange over the seal.

Rolls-Royce 250 Turbine To Gearbox Attach Bolt Wrenches - 3pcs

No longer will you need to use that calibrated elbow. We have designed 3 wrenches to perform the torque checks on the 6 turbine to gearbox attach bolts on the RR250-C30 and C47 engines. A long 1/4" extension will be required to torque the bolt above the...

Rolls-Royce 250 C30/C47 Short Fuel Nozzle Wrench

 RR P/N 23007638

Rolls-Royce 250 C30/C47 Fuel Nozzle Wrench

This fuel nozzle wrench is double sided to give you better access to the fuel nozzle. With the cowling installed, if you place the wrench on the fuel nozzle, it may not sit the way you want because of the limited space, flip it to the other side. The...

Rolls-Royce 250 C30/C47 Medium Fuel Nozzle Wrench

This wrench is usually preferred by the overhaul guys working the engine on a stand.

206B Bleed Valve Block

Color varies when manufactured Bleed valve block for Rolls-Royce C20 engine with strap so that it can be hung. Rolls-Royce P/N 6886204

Rolls-Royce 250-C20/C30/C47 Engine Lifting Eye

Engine lifting eye for C20, C30, and C47. Long enough to clear the exhaust stack so it doesn't have to be removed. Rolls-Royce C20 6796963Rolls-Royce C30/C47 6889888

Rolls-Royce 250 Ignitor Wrench

Ignitors can be hard to remove for several reasons. Someone put it in too tight, didn't use anti-seize or used a 12 point socket and slipped, rounding off the corners. This wrench is made from a 6 point impact socket. Install the wrench and put the...

Rolls-Royce 250 Starter/Generator Spline Turn Wrench

T-handle wrench for turning the N1 wheels while doing maintenance on the RR250 series engines. Starter/generator splines are hard to find, so get yours here   Rolls-Royce P/N 6799790

Rolls-Royce 250 Idle Adjustment Swing Wrench

This swing wrench is made specifically for adjusting the idle on the 206 RR250 engine. Of course with that in mind, you can also use it for any tight spot that requires a 1/4" box end wrench. We have 2 types of swing wrenches. Our version and Helitools'...

Rolls-Royce 250 Exhaust Stack Wrench

Wrench is made for removal of the nuts on the exhaust stack. Keeps nuts from falling into crevices of the engine.

Rolls-Royce 250 C30/C47 Gearbox PTO Seal Installer

This installer works on the C30 and C47 engines.  You can install one seal at a time or both at once. This is the best seal installer you will find for the gearbox seals.

Rolls-Royce 250 C30/C47 Gearbox PTO Seal Remover

Removes rear gearbox seal.

Rolls-Royce 250 C30/C47 Bleed Valve Shop Air Adapter

Quick disconnect so that you can use shop air to close the Bleed valve.

Rolls-Royce 250 Quick Disconnect Coupling For Engine Rinse

Name says it all.

Rolls-Royce 250 Power Turbine Support Cleaning Kit

Kit comes in a foam insert for easy storage and handling. Keep the cardboard box it comes in for added protection.   RR P/N 23007615

Torque Adapters 1/4" Drive

Hard to find 1/4" drive torque adapters. Most torque adapters you will find are 3/8" drive. These will allow you to use that low torque 1/4" torque wrench without the 3/8" to 1/4" adapter.   SAE: The standard set consists of 1/4", 5/16", 3/8", &...

222 Engine Oil Drain

Typical  engine oil drain. Comes with a 7 ft hose.

407 HTS900 Accessory Gearbox Drain

Oil drain hose for the accessory gearbox on the 407 powered by the Honeywell engine.Won't find too many of these out there. Comes with a 7 ft hose.

RR250 C30/C47 Compressor/Diffuser Orifice R&R Work Aid

Use this work aid to remove and re-install the orifice when it is located in the exhaust collector.Good on any 206L with C30 installed, 407, and Sikorsky S-76A.

Rolls-Royce 250 C47 Engine Gearbox Drain

As you know, the C47 has the quick disconnect chip detectors that have the self plugging housing. Unlike the C30's that will drain when you pull the chip detectors, the C47 requires this work aid to drain the gearbox. This drain is made from steel.

Rolls-Royce 250 HMU "Fuel Control" Throttle/Fly Detent Rigging Pin

Easy to handle rigging pin with red streamer.

Rolls-Royce 250-C20 Starter/Generator & Fuel Pump Seal Installer

This is the new seal installer from Rolls-Royce's Commercial Service Letter. This was designed for installing the new lip seals (23091467) which include a supplied installation mandrel.Although it will also work on the old lip seals (23079054) we,...

429 PLA Alignment Guide

Bell 429 PLA alignment aid Lines up the PLA base to the gearbox to prevent side loads on the PLA shaft.

429 Engine Gearbox Drain

Engine gearbox drain comes with a 7 ft hose. 

Pratt & Whitney PW200 Engine Sling

Good on the PW200 series engines.

S76A Main Driveshaft Wrench 2pcs set

Consists of 2 wrenches, one for the front coupling and another for the aft coupling. Does not include ratchet, extension or socket. Makes driveshaft R&R quick and easy and avoids spilling blood all over the transmission deck.On the A...

S76 PTO Shaft Wrench

When removing or installing the PTO shaft on the C30 engine you need this fixture to hold a backup on the shaft and also to apply the correct torque so the PTO gear is not over torqued and cracked.

Turbomeca Engine Oil Filter Wrench

Turbomeca engine oil filter wrench to remove the housing cap on the S1 or S2 engine.

Rolls-Royce 250 Banjo Oil Fitting Wrench

Allows you to tighten the banjo fitting with a ratchet or torque wrench. Makes removal a piece of cake too. S76A only.

Turbomeca 2S1 Oil Drain

Oil drain for the Turbomeca engine. There are 2 types that I have seen so far.

Turbomeca 2S2 Oil Drain

Oil drain for the Turbomeca engine. There are 2 types that I have seen so far.

S76D Engine Oil Sump

Name explains usage.

S76D Engine Oil Drain

Drains oil through chip plug.

S76C Main Driveshaft Alignment Rod

Used to check the main drive shaft alignment when changing engine mounts or any time an alignment problem is suspected. Normally companies furnish this rod but too often it doesn't make it back to the right place in the tool crib so when you need it, it...

S92 Engine Oil Drain

We have the engine oil drain at a lot lower price than the manufacturer.

S92 Hydraulic Oil Drain

M01 and M05 MODULE OIL DRAIN HOSE

Drain hose for the M01 and M05 modules. Comes with a 7 foot hose.

AS350 Engine Oil Drain

The AS350 engine oil and hydraulic oil tanks use the same drain.This drain comes with a 7 ft hose just like all the rest.

AS350 Starter/Generator Seal Installer

Installs and seats the seal into the flange housing with air pressure. 8813824000

EC135 Engine Oil Drain

Comes with a 7 ft. hose.

EC145 Engine Oil Drain

Comes with a 7 ft. hose

Rolls-Royce RR300 Seal Installer

This is the new seal installer from Rolls-Royce's Commercial Service Letter. This was designed for installing the new lip seals (23091467) which include a supplied installation mandrel.

Rolls-Royce 300 Aft PTO Seal Installer

Name describes it all.

Rolls-Royce 300 PTO Seal Remover

Name describes it all.

Robinson Spark Plug Ignition Cable Wrench

Rolls-Royce 250 Oil Pressure Regulator Socket

1/4 inch drive socket for adjusting the oil pressure regulator.Makes it easy to adjust and count the turns plus it won't eat up the regulator adjusting bar when using needle nose pliers like other people used to do.

Rolls-Royce 250 Turbine Wheel Lock

Used to lock the turbine wheel in place when installing the turbine section. The plate and rod are made from brass. The brass rod is soft enough to bend if necessary so it won't damage the turbine blades should excessive pressure be applied to the...

Rolls-Royce 250 St. Gobain PTO Seal Installer

These are the seal installers for the new St Gobain seals p/n 23091293 (red) and p/n 23091353 (blue)They can also be used for installing the Viton SealsThe C20 and C30/47 have different seal insertion depths so order according to your engine model

Honeywell HTS900 NP Sensor Shimming Work Aid

Used for shimming the NP Sensor. Screw the large piece, adapter or bushing or whatever you want to call it into the gearbox.   Screw in the center bolt until it contacts the gear tooth.​Lock it down using the knurled nut...

S92 APU Oil Drain

APU gearbox drain with 7 ft hose

RR250-C30/C47 Spur Adapter Gear O'ring Installation Work Aid

For engines C30 and C47 only RR P/N 23006785

407 HTS900 Engine Oil Filter Socket & Wrench

This socket removes the oil filter housing on the HTS900 engine.​Socket is removed with a 3/4" flex ratcheting box end wrench. We have the wrench if you don't have the flex style which makes it much easier to get on the attached nut.

Oil Can Opener

One Black Plastic "Church Key" FOD Free Turbine Oil Can Opener

Rolls-Royce 250 Starter/Generator Seal Installer & Fuel Pump Seal Installer - 2pcs

This work aid is a 2 in 1. Use it on either the starter/generator seal or the fuel pump seal. Simplifies installation of seals and removes chances of damaging seal while installing.  This work aid is only for lip seal (23079054).

GE - CT-7 FUEL FILTER WRENCH

Ratcheting 5/8 - 3/8 drive wrench for R&R of fuel filter bowl on the GE CT-7 engine

Rolls-Royce 250 PTO Seal Remover

Used to remove single lip PTO seal on RR250 engines.   Thread into the seal and use slide hammer to remove.

429 PW207 Mag Seal Puller

Slide Hammer used to remove Seal P/N 3058291-01   PWC64888 PWC64888-1    Designed with customer to fit tighter than PWC factory workaid. All 3 lips engage. 

C30/47 #1 Bearing in Compressor Puller

C30/47 #1 Bearing in Compressor Puller   23005023